Click here to ask about the production status of specific part numbers.
MAX22200
36V, 1A Octal Integrated Serial-Controlled
Solenoid and Motor Driver
General Description
Benefits and Features
The MAX22200 is an octal 36V serial-controlled solenoid
driver. Each channel features a low impedance (200mΩ
typ) push-pull output stage with sink-and-source driving
● Eight Half-Bridges Up To +36V
● High Performances:
• Low On-Resistance: R
+25°C)
: 200 mΩ typical (T =
A
DS(on)
capability and up to 1A
driving current. A serial inter-
RMS
face (SPI) that also supports daisy-chain configurations is
• Continuous Output Current Up To 1A
per Half-
RMS
provided to individually control each channel.
Bridge (T = +25°C)
A
• Current-Drive Regulation (CDR)
• Voltage-Drive Regulation (VDR)
• Integrated Lossless Current Sensing (ICS)
The device half-bridges can be configured as low-side
drivers or as high-side drivers. Moreover, pairs of half-
bridges can be paralleled to double the driving current or
can be configured as full-bridges to drive up to four latched
valves (bi-stable valves) or four brushed DC motors.
● High Flexibility:
• Independent Programmable HIT and HOLD
Currents for Each Channel (I , I
)
HIT HOLD
Two control methods are supported: voltage drive regu-
lation (VDR) and current drive regulation (CDR). In VDR,
the device outputs a PWM voltage in which the duty cycle
is programmed using SPI. For a given supply voltage and
solenoid resistor, the output current is proportional to the
programmed duty cycle. In CDR, an internal integrated
lossless current sensing (ICS) circuit senses the output
current and compares it with an internal programmable
reference current.
• Independent Programmable HIT Current Timing for
Each Channel (t
)
HIT
• Full-Bridge Configuration Supported
• Parallel Mode Supported
● High Speed Serial Interface (SPI)
• 5MHz Daisy-Chain Configuration
• 10MHz without Daisy Chain
● Protections and Diagnostic
For optimal power management in solenoid drive applica-
• Overcurrent Protection (OCP)
• Open-Load Detection (OL)
tions, the excitation drive level (I ), the hold drive level
HIT
(I
), and the excitation drive time (t ) can be individ-
• Detection of Plunger Movement (DPM)
• Undervoltage Lockout (UVLO)
• HIT Current Not Reached (HHF)
• Thermal Shutdown T = +145°C (TSD)
• Fault Registers for Diagnostic purposes
HOLD
HIT
ually configured for each channel.
The MAX22200 features a full set of protections and di-
agnostic functions. This includes overcurrent protection
(OCP), thermal shutdown (TSD), undervoltage Lockout
(UVLO), open-load detection (OL), and detection of
plunger movement (DPM). A fault indication pin (FAULT)
signals fault events and diagnostic information is stored in
the FAULT register.
● Integration:
• 32 TQFN 5mm x 5mm Package
Ordering Information appears at end of datasheet.
Due to the flexibility of use, the serial interface control,
the high efficiency, and the small package, the MAX22200
is particularly well-suited for solenoid driver applications
(valve control, relays control etc.) in which low power con-
sumption and high level of integration are required.
The MAX22200 is available in a compact 5mm x 5mm,
32-pin TQFN package and operates over the temperature
-40ºC to +85ºC range.
Applications
● Relays Driver
● Solenoid, Valves, Electromagnetic Drivers
● Generic Low-Side and High-Side Switch Applications
● Latched (Bi-Stable) Solenoid Valve Drivers
● Brushed DC Motor Driver
19-100531; Rev 0; 4/20