Click here to ask an associate for production status of specific part numbers.
36V, 3.5A Brushed Motor Driver with
Integrated Current Sense
MAX22201/MAX22202/
MAX22207
General Description
Benefits and Features
The MAX22201/MAX22202/MAX22207 integrate one
36V, 3.5A peak full bridge capable of driving one brushed
DC motor. The full bridge features very low impedance
● One Full H-Bridge with +36V Voltage Rating
● Total R
(High Side + Low Side): 300mΩ (typ)
DS(ON)
(T = +25°C)
A
FETs with a typical R
(high side + low side) of 0.3Ω re-
● Current Ratings (+25°C typ)
ON
sulting in high driving efficiency. The peak current rating
of 3.5A is limited by the overcurrent protection threshold
(OCP). The peak current is defined as the maximum cur-
rent the driver can provide for short transients. The maxi-
mum RMS current is 2A and is typically limited by thermal
• I
• I
= 3.5A
= 2A
PEAK
RMS
● Configurable Current Drive Regulation (CDR) for
Limiting Stall and Inrush Current
• Configurable Off Time (t
only)
) for CDR (MAX22201
OFF
considerations. The 2A
capability refers to a standard
RMS
JEDEC 4-layer board at 25°C ambient temperature. The
real operating maximum current depends on the appli-
cation thermal characteristic (PCB ground planes, heat
sinks, ventilation, etc.).
● Lossless Integrated Current Sensing (ICS) Eliminates
External Bulky Resistors and Saves Power
● Current Sense Output (CSO) Function: A Replica of
the Internally Sensed Current is Output on the ISEN
Pin
● Current Drive Regulation Monitor (CDROUT)
(MAX22207 only)
● Fault Indicator pin (FAULT)
The MAX22201/MAX22202/MAX22207 feature a non-dis-
sipative and accurate integrated current sensing (ICS) and
an embedded internal current drive regulation (CDR) cir-
cuit to monitor the current through a motor coil and limit
the peak output current. When the motor current exceeds
the current limit threshold, the full bridge enters a decay
● Fully Integrated Charge Pump
● Protections
mode for a fixed off time (t
). For brushed motor drive
OFF
• Overcurrent Protection for Each Individual Channel
(OCP)
• Undervoltage Lockout (UVLO)
• Thermal Shutdown (TSD) T = +165°C
• ESD Protection 8kV HBM (OUT1 and OUT2 Pins)
applications, the current drive regulation guarantees safe
and reliable operation of the driver under normal condi-
tions or during motor startup and stall conditions, and al-
so reduces system power and supply bypassing require-
ments. A scaled copy of the internally sensed current is
output to an external pin (ISEN). For more information on
these features, refer to the Detailed Description.
● Ultra-Small Package TDFN12 3mm x 3mm
All versions feature overcurrent protection (OCP), thermal
shutdown (TSD), and undervoltage lockout (UVLO). An
open-drain active-low fault indication pin (FAULT) is acti-
vated every time a fault condition is detected.
The device is packaged into a tiny TDFN12 3mm x 3mm
package. The small package footprint, the extremely high
efficiency and the integrated accurate current sensing
make the MAX22201/MAX22202/MAX22207 an excellent
choice for space- and power-sensitive applications.
Applications
● Brushed DC Motor Drive
● Stepper Motor Drive (One Phase Only)
● Latched Valves and Solenoids
19-100898; Rev 2; 1/22
Ordering Information appears at end of datasheet.
© 2022 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.
One Analog Way, Wilmington, MA 01887 U.S.A. | Tel: 781.329.4700 | © 2022 Analog Devices, Inc. All rights reserved.