CDMA Cellular/PCS System
Power Supplies
ABSOLUTE MAXIMUM RATINGS
OFF, DR1, DR2 to GND............................................-0.3V to +6V
IN1, IN2/3, IN4/5, DIN (SDA) to GND.......................-0.3V to +6V
SCLK (SCK), BP, ON to GND...................................-0.3V to +6V
Continuous Sink Current
DR1, DR2...............................................................100mA
RMS
RSO................................................................................25mA
Continuous Power Dissipation (T = +70°C)
RSO, ONO to GND .................................-0.3V to (V
+ 0.3V)
A
OUT1
20-Pin QFN (derate 20mW/°C above +70°C) .................1.6W
20-Pin TSSOP (derate 26mW/°C above +70°C) .............2.1W
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature......................................................+150°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
PGND to GND..................................................................... 0.3V
OUT1, CS (AS) to GND..............................-0.3V to (V
+ 0.3V)
+ 0.3V)
+ 0.3V)
IN1
IN2/3
IN4/5
OUT2, OUT3 to GND...............................-0.3V to (V
OUT4, OUT5 to GND...............................-0.3V to (V
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
= V
= V
= V
= V
= V
= V
= 3.6V; ON = GND = PGND = 0; RSO, ONO, DR1, DR2 =
OFF
IN1
IN2/3
IN4/5
SCLK (SCK)
DIN (SDA)
CS (AS)
open; BP bypassed with 0.01µF, OUT1 bypassed with 4.7µF; OUT2, OUT3, OUT4, OUT5 bypassed with 2.2µF; OUT1–5 set to 2.98V,
= 0°C to +85°C, unless otherwise noted. Typical values are at T = +25°C.)
T
A
A
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
IN1, IN2/3, IN4/5 Operating
Voltage
2.5
5.5
V
Undervoltage Lockout IN1
Undervoltage Lockout IN2/3
Undervoltage Lockout IN4/5
Power-On Reset Threshold
Supply Current in Shutdown
Supply Current (Standby)
Supply Current (All Outputs On)
BP Voltage
V
IN1 rising edge
2.10
2.10
2.10
0.9
2.30
2.30
2.30
2.45
2.45
2.45
2.1
V
V
UVLO-1
V
IN2/3 rising edge
UVLO-2/3
UVLO-4/5
V
IN4/5 rising edge
V
IN1 falling edge
V
I
1
10
µA
µA
µA
V
OFF = 0, ON = IN1
OUT1 ON, other regulators OFF I
SHDN
I
= 0
OUT1
113
367
1.250
0.2
230
680
1.269
5
ON
All regulators ON, I
= 0
OUT_
I
BP
1nA
1.231
BP Supply Rejection
2.5V
V
IN1
5.5V
mV
OUT1 REGULATOR
Output Accuracy
I
= 70mA (Note 3)
-2
-3
2
3
%
%
OUT1
Output Accuracy
(Line and Load)
1mA
2.5V
I
300mA,
5.5V, V
OUT1
V
IN1
= 1.8V (Note 3)
OUT1
Nominal Voltage Adjust Range
32 steps through serial interface; Tables 2, 3
1.8
3.3
V
I
I
= 1mA (Notes 1, 3)
1
OUT1
OUT1
Dropout Voltage
mV
= 200mA (Notes 1, 3)
73
125
Load Regulation
Line Regulation
Current Limit
0.1mA
2.5V
I
300mA
-0.003
-0.03
500
%/mA
%/V
OUT1
V
5.5V, V
= 1.8V (Note 3)
OUT1
-0.15
320
0.11
850
IN1
mA
Output-Discharge Switch
Resistance in Shutdown
Regulator output turned off
25
300
(MAX1798/MAX1799)
(MAX1798A/MAX1799A)
= 4.7µF
-9.5
-15
-7.5
-13
45
-5.5
-11
OUT1 rising and
falling
OUT1 Reset Threshold
Output Voltage Noise
%
f = 10Hz to 100kHz, C
µV
OUT
RMS
2
_______________________________________________________________________________________