LTC1164-6
The
●
denotes specifications that apply over the full operating temperature
ELECTRICAL CHARACTERISTICS
range, otherwise specifications are at T = 25°C. V = ±7.5V, R = 10k, T = 25°C, f = 400kHz, TTL or CMOS level (maximum clock
CLK
A
S
L
A
rise or fall time ≤ 1µs) and all gain measurements are referenced to passband gain, unless otherwise specified. (f /f
) = 4kHz
CLK CUTOFF
at 100:1 and 8kHz at 50:1.
PARAMETER
CONDITIONS
V ≥ ±7.5V
MIN
TYP
MAX
UNITS
Maximum f (Table 3)
1.5
1.0
1.0
MHz
MHz
MHz
CLK
S
V ≤ ±5V
S
V = Single 5V, AGND = 2V
S
Clock Feedthrough
Wideband Noise
Input at GND, f = f , Square Wave
CLK
V = ±7.5V, (f /f ) = 100:1
500
200
µV
µV
S
CLK
C
RMS
RMS
V = ±5V, (f /f ) = 50:1
S
CLK C
Input at GND, 1Hz ≤ f < f
CLK
V = ±7.5V
115 ± 5%
100 ± 5%
µV
µV
S
RMS
RMS
kΩ
V = ±2.5V
S
Input Impedance
45
75
110
Output DC Voltage Swing
V = ±2.375V
S
V = ±7.5V
S
●
●
●
±1.25
±3.70
±5.40
±1.50
±4.10
±5.90
V
V
V
S
V = ±5V
Output DC Offset
Output DC Offset Tempco
Power Supply Current
V = ± 5V, (f /f ) = 100:1
±100
±100
2.5
±160
mV
µV/°C
mA
mA
mA
mA
S
CLK C
V = ± 5V, (f /f ) = 100:1
S
CLK C
V = ± 2.375V, T > 25°C
4.0
4.5
7.0
8.0
11.0
12.5
S
A
●
●
●
V = ± 5V, T > 25°C
4.5
7.0
S
A
V = ± 7.5V, T > 25°C
mA
mA
S
A
Power Supply Range
±2.375
±8
V
+
–
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Connecting any pin to voltages greater than V or less than V
may cause latch-up. It is recommended that no sources operating from
external supplies be applied prior to power-up of the LTC1164-6.
Note 3: All gains are measured relative to passband gain.
Note 4: The cutoff frequency of the filter is abbreviated as f
or f .
C
CUTOFF
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Stopband Gain vs Frequency
(Elliptic Response)
Stopband Gain vs Frequency
(Elliptic Response)
10
0
10
V
f
= ±5V
V
f
C
= ±5V
CLK
= 5kHz
S
S
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
= 250kHz
= 500kHz
CLK
(f /f ) = 50:1
f
CLK
C
–10
–20
–30
–40
–50
–60
–70
–80
–90
+
(PIN 10 AT V )
= 25°C
(f /f ) = 100:1
CLK
C
–
T
(PIN 10 AT V )
= 25°C
A
WITH EXTERNAL
SINGLE POLE LOW-
PASS RC FILTER
T
A
(f
= 10kHz)
– 3dB
6
8
10 12 14 16
18
20 22
2
4
6
8
10 12 14 16
18
20
22
2
4
FREQUENCY (kHz)
FREQUENCY (kHz)
1164-6 G01
1164-6 G02
11646fa
3