Spec No.: JELF243A_0086Q-01
No. Item
P3/9
Specification
Test method
8.2 Bending test
No significant mechanical damage or no Test substrate: glass-epoxy substrate (100 mm × 40
sign of electrode peeling off shall be
observed.
mm × 1.0 mm)
Pressurizing speed: 0.5 mm/s
Deflection: 2 mm
Holding time: 5 s
8.3 Vibration
Appearance shall have no significant
mechanical damage.
Oscillation frequency: 10 Hz to 2000 Hz to 10 Hz, for
approx. 20 min
Total amplitude: 1.5 mm
Test time: 3 directions perpendicular to each other, 2 h
for each direction (6 h in total)
8.4 Solderability
90% or more of the outer electrode shall Flux: immersed in ethanol solution with a rosin content
be covered with new solder seamlessly. of 25(wt)% for 5 s to 10 s
Solder: Sn-3.0Ag-0.5Cu solder
Pre-heating: 150°C±10°C/60 s to 90 s
Solder temperature: 240°C±5°C
Immersion time: 3 s±1 s
8.5 Resistance to
soldering heat
Appearance: No significant mechanical Flux: immersed in ethanol solution with a rosin content
damage shall be observed.
of 25(wt)% for 5 s to 10 s
Inductance change rate: within ±10%
Solder: Sn-3.0Ag-0.5Cu solder
Pre-heating: 150°C±10°C/60 s to 90 s
Solder temperature: 270°C±5°C
Immersion time: 10 s±1 s
Post-treatment: left at a room condition for 24 h±2 h
9. Environmental Performance
The product is soldered on a substrate for test.
No.
Item
Specification
Test method
9.1 Heat resistance
9.2 Cold resistance
9.3 Humidity
Appearance: No significant mechanical Temperature: 85°C±2°C
damage shall be observed.
Test time: 1000 h (+48 h, -0 h)
Inductance change rate: within ±10%
DC resistance change rate: within ±10%
Post-treatment: left at a room condition for 24 h±2 h
Appearance: No significant mechanical Temperature: -40°C±2°C
damage shall be observed.
Test time: 1000 h (+48 h, -0 h)
Inductance change rate: within ±10%
DC resistance change rate: within ±10%
Post-treatment: left at a room condition for 24 h±2 h
Appearance: No significant mechanical Temperature: 70°C±2°C
damage shall be observed.
Inductance change rate: within ±10%
Humidity: 90% (RH) to 95% (RH)
Test time: 1000 h (+48 h, -0 h)
DC resistance change rate: within ±10% Post-treatment: left at a room condition for 24 h±2 h
9.4 Temperature cycle Appearance: No significant mechanical Single cycle conditions:
damage shall be observed.
Step 1: -40°C±2°C/30 min±3 min
Inductance change rate: within ±10%
DC resistance change rate: within ±10%
Step 2: ordinary temperature/10 min to 15 min
Step 3: +85°C±2°C/30 min±3 min
Step 4: ordinary temperature/10 min to 15 min
Number of testing: 10 cycles
Post-treatment: left at a room condition for 24 h±2 h
MURATA MFG CO., LTD
5秒后页面跳转
STM32H743技术深度剖析与应用案例探索
LM321中文资料解析：引脚功能介绍、技术特点、技术特性分析
74HC14芯片资料介绍：性能特性分析、引脚介绍
LM1875芯片手册：功放参数分析、引脚说明、电路设计要点
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
