LM4995, LM4995TMBD
SNAS329G –APRIL 2006–REVISED APRIL 2013
www.ti.com
ELECTRICAL CHARACTERISTICS VDD = 5V(1)(2)
The following specifications apply for the circuit shown in Figure 1, unless otherwise specified. Limits apply for TA = 25°C.
LM4995
Typical(3)
Units
(Limits)
Symbol
Parameter
Conditions
Limit(4)(5)
VIN = 0V, Io = 0A, No Load
VIN = 0V, Io = 0A, 8Ω Load
VSD = VGND
1.5
1.8
0.01
5
2.5
mA (max)
mA
IDD
Quiescent Power Supply Current
ISD
VOS
Po
Shutdown Current
Output Offset Voltage
Output Power
1
µA (max)
mV (max)
W
No Load
26
THD+N = 1% (max); f = 1 kHz
1.3 (TM)
1.25 (SD)
TWU
Wake-up time
165
ms
%
THD+N
Total Harmonic Distortion + Noise
Po = 500mWRMS; f = 1kHz
0.08
Vripple = 200mV sine p-p
Input terminated to GND
73 (f = 217Hz)
73 (f = 1kHz)
PSRR
Power Supply Rejection Ratio
dB
VSDIH
VSDIL
Shutdown Voltage Input High
Shutdown Voltage Input Low
1.5
1.2
V
V
(1) All voltages are measured with respect to the ground pin, unless otherwise specified.
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensure for parameters where no limit is given, however, the typical value is a good indication
of device performance.
(3) Typicals are measured at 25°C and represent the parametric norm.
(4) Limits are specified to AOQL (Average Outgoing Quality Level).
(5) Datasheet min/max specification limits are specified by design, test, or statistical analysis.
ELECTRICAL CHARACTERISTICS VDD = 3.6V(1)(2)
The following specifications apply for the circuit shown in Figure 1, unless otherwise specified. Limits apply for TA = 25°C.
LM4995
Typical(3)
Units
(Limits)
Symbol
Parameter
Conditions
Limit(4)(5)
VIN = 0V, Io = 0A, No Load
VIN = 0V, Io = 0A, 8Ω Load
VSD = VGND
1.3
1.6
0.01
5
2.3
mA (max)
mA
IDD
Quiescent Power Supply Current
ISD
Shutdown Current
Output Offset Voltage
Output Power
1
µA (max)
mV (max)
mW
VOS
No Load
26
THD+N = 1% (max); f = 1 kHz
625 (TM)
610 (SD)
Po
TWU
Wake-up time
130
ms
%
THD+N
Total Harmonic Distortion + Noise
Po = 300mWRMS; f = 1kHz
0.07
Vripple = 200mV sine p-p
Input terminated to GND
75 (f = 217Hz)
76 (f = 1kHz)
PSRR
Power Supply Rejection Ratio
dB
VSDIH
VSDIL
Shutdown Voltage Input High
Shutdown Voltage Input Low
1.3
1
V
V
(1) All voltages are measured with respect to the ground pin, unless otherwise specified.
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensure for parameters where no limit is given, however, the typical value is a good indication
of device performance.
(3) Typicals are measured at 25°C and represent the parametric norm.
(4) Limits are specified to AOQL (Average Outgoing Quality Level).
(5) Datasheet min/max specification limits are specified by design, test, or statistical analysis.
4
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM4995 LM4995TMBD