LM4859
www.ti.com
SNAS256E –MAY 2004–REVISED MAY 2013
Audio Amplifier Electrical Characteristics VDD = 3.0V(1)(2)
The following specifications apply for VDD = 3.0V, unless otherwise specified. Limits apply for TA = 25°C.
Symbol
Parameter
Conditions
LM4859
Units
(Limits)
(3)
(4) (5)
Typical
Limits
VIN = 0V, No load;
LD5 = RD5 = 0(6)
Mode 4, 9, 14
IDD
Supply Current
4.5
7.5
mA (max)
mA (max)
µA (max)
Mode 2, 3, 7, 8, 12, 13
Mode 0(6)
11.2
0.06
19
ISD
PO
Shutdown Current
Output Power
2.5
LM4859SP
Speaker; THD+N = 1%;
f = 1kHz; 4Ω BTL
530
mW
Speaker; THD+N = 1%;
f = 1kHz; 8Ω BTL
400
25
320
20
mW (min)
mW (min)
PO
Output Power
Headphone; THD+N = 1%;
f = 1kHz; 32Ω SE
LD5 = RD5 = 0
Speaker; PO = 200mW;
f = 1kHz; 8Ω BTL
Total Harmonic Distortion Plus
Noise
0.05
%
THD+N
VOS
Headphone; PO = 10mW;
f = 1kHz; 32Ω SE
0.04
5
%
Offset Voltage
Output Noise
Speaker; LD5 = RD5 = 0
A-weighted; 0dB gain;(7)
LD5 = RD5 = 0; All Inputs Terminated
40
mV (max)
Speaker; Mode 2, 3, 7, 8
Speaker; Mode 12, 13
27
38
10
14
µV
µV
µV
µV
NOUT
Headphone; Mode 3, 4, 8, 9
Headphone; Mode 13, 14
f = 217Hz, Vrip = 200mVpp; CB = 2.2µF;
0dB gain;(7)
LD5 = RD5 = 0; All Audio Inputs Terminated
Speaker; Mode 2, 3, 7, 8
Speaker; Mode 12, 13,
Headphone; Mode 3, 4, 8, 9
Headphone; Mode 13, 14
LD5 = RD5 = 0
70
65
87
75
dB
PSRR
Power Supply Rejection Ratio
55
62
dB (min)
dB
dB (min)
Loudspeaker; PO = 200mW;
f = 1kHz
82
82
dB
dB
Xtalk
TWU
Crosstalk
Headphone; PO = 10mW;
f = 1kHz
CD5 = 0; CB = 2.2µF
CD5 = 1; CB = 2.2µF
80
ms
ms
Wake-up Time
140
(1) All voltages are measured with respect to the GND pin unless otherwise specified.
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
(3) Typicals are measured at +25°C and represent the parametric norm.
(4) Limits are ensured to Texas Instruments' AOQL (Average Outgoing Quality Level).
(5) Datasheet min/max specification limits are specified by design, test, or statistical analysis.
(6) Shutdown current and supply current are measured in a normal room environment. All digital input pins are connected to I2CVDD
(7) “0dB gain” refers to the volume control gain setting of MIN, LIN, and RIN set at 0dB.
.
Copyright © 2004–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM4859