5秒后页面跳转
LM136H-5.0/883 PDF预览

LM136H-5.0/883

更新时间: 2024-02-11 03:14:28
品牌 Logo 应用领域
美国国家半导体 - NSC 电源电路参考电压源二极管
页数 文件大小 规格书
11页 220K
描述
5.0V Reference Diode

LM136H-5.0/883 技术参数

生命周期:Active零件包装代码:TO-46
包装说明:TO-46, 3 PIN针数:3
Reach Compliance Code:not_compliantECCN代码:EAR99
HTS代码:8542.39.00.01Factory Lead Time:1 week
风险等级:1.24Is Samacsys:N
其他特性:ADJUSTABLE FROM 4V TO 6V模拟集成电路 - 其他类型:TWO TERMINAL VOLTAGE REFERENCE
JESD-30 代码:O-MBCY-W3长度:4.699 mm
湿度敏感等级:1功能数量:1
输出次数:1端子数量:3
最高工作温度:125 °C最低工作温度:-55 °C
最大输出电压:5.1 V最小输出电压:4.9 V
标称输出电压:5 V封装主体材料:METAL
封装代码:TO-46封装等效代码:CAN3/4,.1
封装形状:ROUND封装形式:CYLINDRICAL
峰值回流温度(摄氏度):NOT SPECIFIED认证状态:Not Qualified
筛选级别:MIL-STD-883座面最大高度:2.362 mm
子类别:Voltage References最大供电电压 (Vsup):6 V
最小供电电压 (Vsup):4 V表面贴装:NO
技术:BIPOLAR最大电压温度系数:222.22 ppm/ °C
温度等级:MILITARY端子形式:WIRE
端子位置:BOTTOM处于峰值回流温度下的最长时间:NOT SPECIFIED
微调/可调输出:YES最大电压容差:2%
宽度:4.699 mmBase Number Matches:1

LM136H-5.0/883 数据手册

 浏览型号LM136H-5.0/883的Datasheet PDF文件第1页浏览型号LM136H-5.0/883的Datasheet PDF文件第2页浏览型号LM136H-5.0/883的Datasheet PDF文件第3页浏览型号LM136H-5.0/883的Datasheet PDF文件第5页浏览型号LM136H-5.0/883的Datasheet PDF文件第6页浏览型号LM136H-5.0/883的Datasheet PDF文件第7页 
Typical Performance Characteristics  
Reverse Voltage Change  
Zener Noise Voltage  
Dynamic Impedance  
DS005716-17  
DS005716-19  
DS005716-18  
Response Time  
Reverse Characteristics  
DS005716-20  
DS005716-21  
Temperature Drift  
Forward Characteristics  
DS005716-23  
DS005716-22  
Application Hints  
The LM136-5.0 series voltage references are much easier to  
use than ordinary zener diodes. Their low impedance and  
wide operating current range simplify biasing in almost any  
circuit. Further, either the breakdown voltage or the tempera-  
ture coefficient can be adjusted to optimize circuit perfor-  
mance.  
If minimum temperature coefficient is desired, four diodes  
can be added in series with the adjustment potentiometer as  
shown in Figure 2. When the device is adjusted to 5.00V the  
temperature coefficient is minimized. Almost any silicon sig-  
nal diode can be used for this purpose such as a 1N914,  
1N4148 or a 1N457. For proper temperature compensation  
the diodes should be in the same thermal environment as  
the LM136-5.0. It is usually sufficient to mount the diodes  
near the LM136-5.0 on the printed circuit board. The abso-  
lute resistance of the network is not critical and any value  
from 2k to 20k will work. Because of the wide adjustment  
range, fixed resistors should be connected in series with the  
pot to make pot setting less critical.  
Figure 1 shows an LM136-5.0 with a 10k potentiometer for  
adjusting the reverse breakdown voltage. With the addition  
of R1 the breakdown voltage can be adjusted without affect-  
ing the temperature coefficient of the device. The adjustment  
range is usually sufficient to adjust for both the initial device  
tolerance and inaccuracies in buffer circuitry.  
www.national.com  
4

与LM136H-5.0/883相关器件

型号 品牌 描述 获取价格 数据表
LM136H5.0/883B TI IC,VOLT REFERENCE,FIXED,5V,BIPOLAR,CAN,3PIN,METAL

获取价格

LM136H-5.0/883B ETC Voltage Reference

获取价格

LM136H5.0/883C TI IC,VOLT REFERENCE,FIXED,5V,BIPOLAR,CAN,3PIN,METAL

获取价格

LM136H-5.0/883C ETC Voltage Reference

获取价格

LM136H-5.0/NOPB TI 5.0 V 基准二极管 | NDV | 3 | -55 to 125

获取价格

LM137 NSC 3-Terminal Adjustable Negative Regulators

获取价格