DESIGN STEPS TO USING THE HS SERIES (CONT.)
ONLINE RESOURCES
Creation of Control Permissions
®
DATA OUT
DATA IN
www.linxtechnologies.com
• Latest News
MODE_IND
2
4
CREATE KEY BUTTON
LEARN BUTTON
1
3
SEND COPY BUTTON
• Data Guides
KEY IN
KEY OUT
• Application Notes
• Knowledgebase
• Software Updates
Figure 10: Steps to Create Control Permissions
1. On the decoder, set the LEARN line high, then take it low to enter Learn Mode.
2. While the decoder’s MODE_IND line is toggling high / low, set a data line on the
encoder high, then low. Repeat for each line to which permission will be granted.
If you have questions regarding any Linx product and have Internet access,
make www.linxtechnologies.com your first stop. Our website is organized in an
intuitive format to immediately give you the answers you need. Day or night, the
Linx website gives you instant access to the latest information regarding the
products and services of Linx. It’s all here: manual and software updates,
application notes, a comprehensive knowledgebase, FCC information, and much
more. Be sure to visit often!
3. After all the desired data lines have been selected, set the LEARN line high,
then low again, or wait until the 17-second time-out occurs. The permissions will
now be saved in the decoder.
4. Select the data lines during an actual transmission to confirm that the
permissions have been successfully created.
USING THE OPTIONAL ENCODER PIN
Creation of an encoder PIN
1. Set the CREATE line high, then low to enter Create
PIN Mode. The MODE_IND line will begin toggling
www.antennafactor.com
high / low until either a PIN is successfully entered
or 15 seconds has passed.
MODE_IND
The Antenna Factor division of Linx offers
a diverse array of antenna styles, many of
which are optimized for use with our RF
modules. From innovative embeddable
antennas to low-cost whips, domes to
Yagis, and even GPS, Antenna Factor
likely has an antenna for you, or can
design one to meet your requirements.
2. To enter the PIN, set high then low a sequence of
2
any four data lines. The MODE_IND will stop
4
}
toggling and the PIN will be created.
3. To cancel the Create PIN Mode prior to the fourth
entry, either wait for the 15 second timeout to pass
or set and clear the CREATE line. The MODE_IND
will stop toggling and no PIN will be created.
1
CREATE
KEY IN
3
4. If a new KEY is created, the PIN will be Figure 11: Encoder PIN Setup
automatically erased.
Using the PIN
www.connectorcity.com
1. The PIN is entered by setting each data line high, then taking it low until all four
entries have been made. There is a maximum 2-second time limit between
entries after which the PIN must be reentered in its entirety.
Through its Connector City division, Linx offers a wide
selection of high-quality RF connectors, including FCC
compliant types such as RP-SMAs that are an ideal
match for our modules and antennas. Connector City
focuses on volume OEM requirements, which allows
standard and custom RF connectors and cable
assemblies to be offered at a low cost.
2. Once the PIN is successfully entered, the encoder will be operational unless it
is inactive for a period longer than what is chosen by the SEL_TIMER line, in
which case PIN reentry would be necessary.
Page 14
Page 15
5秒后页面跳转
深入解析CS8416引脚说明、参数、技术特点
TPA3116D2功放芯片参数详解、引脚说明
移位寄存器74HC165引脚说明、驱动程序示例解读
深入解析AD9833：DDS频率合成器的卓越性能与广泛应用
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
