MLCC Tin/Lead Termination “B”
C0G (NP0) – Specifications and Test Methods
Parameter/Test
Operating Temperature Range
Capacitance
NP0 Specification Limits
Measuring Conditions
-55ºC to +125ºC
Temperature Cycle Chamber
Within specified tolerance
Freq.: 1.0 MHz ± 10% for cap ≤ 1000 pF
1.0 kHz ± 10% for cap > 1000 pF
Voltage: 1.0Vrms ± .2V
<30 pF: Q≥ 400+20 x Cap Value
≥30 pF: Q≥ 1000
Q
100,000MΩ or 1000MΩ - μF,
whichever is less
Charge device with rated voltage for
60 ± 5 secs @ room temp/humidity
Insulation Resistance
Charge device with 250% of rated voltage for
1-5 seconds, w/charge and discharge current
limited to 50 mA (max)
Dielectric Strength
No breakdown or visual defects
Note: Charge device with 150% of rated voltage
for 500V devices.
Appearance
Capacitance
No defects
Deflection: 2mm
Test Time: 30 seconds
±5% or ±.5 pF, whichever is greater
Meets Initial Values (As Above)
≥ Initial Value x 0.3
Resistance to
Flexure
Stresses
Variation
Q
Insulation
Resistance
≥ 95% of each terminal should be covered
Dip device in eutectic solder at 230 ± 5ºC
Solderability
with fresh solder
for 5.0 ± 0.5 seconds
Appearance
No defects, <25% leaching of either end terminal
≤ ±2.5% or ±.25 pF, whichever is greater
Meets Initial Values (As Above)
Capacitance
Variation
Dip device in eutectic solder at 260ºC for 60
seconds. Store at room temperature for 24 ± 2
hours before measuring electrical properties.
Resistance to
Solder Heat
Q
Insulation
Resistance
Meets Initial Values (As Above)
Dielectric
Strength
Appearance
Meets Initial Values (As Above)
No visual defects
Step 1: -55ºC ± 2º
30 ± 3 minutes
Capacitance
Variation
≤ ±2.5% or ±.25 pF, whichever is greater
Step 2: Room Temp
≤ 3 minutes
Q
Meets Initial Values (As Above)
Meets Initial Values (As Above)
Step 3: +125ºC ± 2º
Step 4: Room Temp
30 ± 3 minutes
Thermal Shock
Insulation
Resistance
≤ 3 minutes
Dielectric
Strength
Appearance
Repeat for 5 cycles and measure after
24 hours at room temperature
Meets Initial Values (As Above)
No visual defects
Capacitance
Variation
≤ ±3.0% or ± .3 pF, whichever is greater
Charge device with twice rated voltage in test
chamber set at 125ºC ± 2ºC
≥ 30 pF:
≥10 pF, <30 pF:
<10 pF:
Q≥ 350
Q≥ 275 +5C/2
Q≥ 200 +10C
for 1000 hours (+48, -0).
Q
Load Life
Remove from test chamber and stabilize at room
temperature for 24 hours
Insulation
Resistance
≥ Initial Value x 0.3 (See Above)
before measuring.
Dielectric
Strength
Appearance
Meets Initial Values (As Above)
No visual defects
Capacitance
Variation
≤ ±5.0% or ± .5 pF, whichever is greater
Store in a test chamber set at 85ºC ± 2ºC/ 85% ±
5% relative humidity for 1000 hours
≥ 30 pF:
≥10 pF, <30 pF:
<10 pF:
Q≥ 350
Q≥ 275 +5C/2
Q≥ 200 +10C
Q
(+48, -0) with rated voltage applied.
Load
Humidity
Remove from chamber and stabilize at room
temperature for 24 ± 2 hours before measuring.
Insulation
≥ Initial Value x 0.3 (See Above)
Meets Initial Values (As Above)
Resistance
Dielectric
Strength
40
112916
5秒后页面跳转
STM32H743技术深度剖析与应用案例探索
LM321中文资料解析：引脚功能介绍、技术特点、技术特性分析
74HC14芯片资料介绍：性能特性分析、引脚介绍
LM1875芯片手册：功放参数分析、引脚说明、电路设计要点
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
