JFC20 Series
Single & Dual Outputs
2:1 Input Voltage Range
Rev. A
20 Watt DC/DC Power Converters
MODEL SELECTION TABLES
SINGLE OUTPUT MODELS
Output Current
Min. Load Full Load No Load (3) Full Load (2)
Input Current
Input Voltage
Range
Output
Voltage
Output (4)
Ripple & Noise
Output
Power
Maximum (5)
Capacitive Load
Model Number
Efficiency (4)
JFC12S3.3-20
JFC12S5-20
JFC12S12-20
JFC12S15-20
JFC24S3.3-20
JFC24S5-20
JFC24S12-20
JFC24S15-20
JFC48S3.3-20
JFC48S5-20
JFC48S12-20
JFC48S15-20
3.3 VDC
5 VDC
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
4500mA
4000mA
1670mA
1330mA
4500mA
4000mA
1670mA
1330mA
4500mA
4000mA
1670mA
1330mA
10mA
10mA
10mA
10mA
6mA
6mA
6mA
6mA
4mA
4mA
4mA
4mA
1510mA
1960mA
1960mA
1960mA
746mA
969mA
969mA
958mA
373mA
490mA
484mA
484mA
75mVp-p
75mVp-p
100mVp-p
100mVp-p
75mVp-p
75mVp-p
100mVp-p
100mVp-p
75mVp-p
75mVp-p
100mVp-p
100mVp-p
14.85W
20W
86%
89%
89%
89%
87%
90%
90%
91%
87%
89%
90%
90%
7000µF
5000µF
850µF
700µF
7000µF
5000µF
850µF
700µF
7000µF
5000µF
850µF
700µF
12 VDC
(9 – 18 VDC)
12 VDC
15 VDC
3.3 VDC
5 VDC
20W
20W
14.85W
20W
24 VDC
(18 – 36 VDC)
12 VDC
15 VDC
3.3 VDC
5 VDC
20W
20W
14.85W
20W
48 VDC
(36 – 75 VDC)
12 VDC
15 VDC
20W
20W
DUAL OUTPUT MODELS
Output Current
Min. Load Full Load No Load (3) Full Load (2)
Input Current
Input Voltage
Range
Output
Voltage
Output (4)
Ripple & Noise
Output
Power
Maximum (5)
Capacitive Load
Model Number
Efficiency (4)
JFC12D12-20
JFC12D15-20
JFC24D12-20
JFC24D15-20
JFC48D12-20
JFC48D15-20
±12 VDC
±15 VDC
±12 VDC
±15 VDC
±12 VDC
±15 VDC
0mA
0mA
0mA
0mA
0mA
0mA
±833mA
±667mA
±833mA
±667mA
±833mA
±667mA
10mA
10mA
6mA
6mA
4mA
4mA
1960mA
1938mA
969mA
969mA
490mA
484mA
100mVp-p
100mVp-p
100mVp-p
100mVp-p
100mVp-p
100mVp-p
20W
20W
20W
20W
20W
20W
89%
90%
90%
90%
89%
90%
±500µF
±350µF
±500µF
±350µF
±500µF
±350µF
12 VDC
(9 – 18 VDC)
24 VDC
(18 – 36 VDC)
48 VDC
(36 – 75 VDC)
NOTES
1. BELLCORE TR-NWT-000332. Case 1: 50% Stress, Temperature at 40°C.
MIL-HDBK-217F Notice2 @Ta=25°C, Full load (Ground, Benign, controlled environment).
2. Maximum value at nominal input voltage and full load.
3. Typical value at nominal input voltage and no load.
4. Typical value at nominal input voltage and full load.
5. Test by minimum Vin and constant resistive load.
6. Trimming allows the user to increase or decrease the output voltage set point of the module. This is accomplished by connecting an external resistor
between the TRIM pin and either the +Vout pin or the –Vout pin.
7. The ON/OFF control pin is referenced to –Vin. To order Negative Logic Remote ON/OFF add the suffix “R” to the model number.
8. Heatsink is optional and P/N: 7G-0047C-F. See “Product Standard Table” on page 5 for ordering information.
9. EN55022
1) To meet Class A the module needs no external components
2) To meet Class B please refer to the filter suggestion on page 4.
10. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor suggested is Nippon
chemi-con KY series, 220μF /100V, ESR 48mΩ.
11. There are several different options available for this series. Please see the “Product Standard Table” on page 5 for all options and ordering
information.
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833
09/24/2010
603-778-2300 www.wallindustries.com Fax 603-778-9797
Page 3 of 5