Datasheet > ISL6520AIB

ISL6520AIB

更新时间： 2024-02-24 14:04:45

品牌	Logo	应用领域
罗彻斯特 - ROCHESTER		开关光电二极管
页数	文件大小	规格书
13页	976K
描述
SWITCHING CONTROLLER, 340 kHz SWITCHING FREQ-MAX, PDSO8, PLASTIC, MS-012-AA, SOIC-8

阅读下载

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

ISL6520AIB 技术参数

是否无铅：	含铅	生命周期：	Active
零件包装代码：	SOIC	包装说明：	SOP,
针数：	8	Reach Compliance Code：	unknown
风险等级：	5.09	Is Samacsys：	N
模拟集成电路 - 其他类型：	SWITCHING CONTROLLER	控制模式：	VOLTAGE-MODE
控制技术：	PULSE WIDTH MODULATION	最大输入电压：	5.5 V
最小输入电压：	4.5 V	标称输入电压：	5 V
JESD-30 代码：	R-PDSO-G8	JESD-609代码：	e0
长度：	4.9 mm	湿度敏感等级：	1
功能数量：	1	端子数量：	8
最高工作温度：	85 °C	最低工作温度：	-40 °C
封装主体材料：	PLASTIC/EPOXY	封装代码：	SOP
封装形状：	RECTANGULAR	封装形式：	SMALL OUTLINE
峰值回流温度（摄氏度）：	240	座面最大高度：	1.75 mm
表面贴装：	YES	切换器配置：	PUSH-PULL
最大切换频率：	340 kHz	温度等级：	INDUSTRIAL
端子面层：	TIN LEAD	端子形式：	GULL WING
端子节距：	1.27 mm	端子位置：	DUAL
处于峰值回流温度下的最长时间：	30	宽度：	3.9 mm
Base Number Matches：	1

ISL6520AIB 数据手册

ISL6520A

controlled output voltage rise. The entire startup sequence

typically take about 11ms.

OUTPUT INDUCTOR

CURRENT

5A/DIV.

OUT

500mV/DIV.

COMP/OCSET

1V/DIV.

TIME (5ms/DIV.)

FIGURE 1. OVERCURRENT OPERATION

The overcurrent function will trip at a peak inductor current

TIME (2ms/DIV.)

determined by Equation 3:

PEAK)

FIGURE 2. SOFT-START INTERVAL

x R

OCSET

= ----------------------------------------------------

PEAK

DS(ON)

(EQ. 3)

Current Sinking

The ISL6520A incorporates a MOSFET shoot-through

protection method which allows a converter to sink current

as well as source current. Care should be exercised when

designing a converter with the ISL6520A when it is known

that the converter may sink current.

where I

is the internal OCSET current source (20µA

OCSET

typical). The OC trip point varies mainly due to the

MOSFET’s r variations. To avoid overcurrent tripping

DS(ON)

in the normal operating load range, find the R

from the equation above with:

resistor

OCSET

When the converter is sinking current, it is behaving as a

boost converter that is regulating it’s input voltage. This

1. The maximum r

temperature.

at the highest junction

DS(ON)

means that the converter is boosting current into the V

rail, which supplies the bias voltage to the ISL6520A. If there

is nowhere for this current to go, such as to other distributed

2. The minimum I

3. Determine I

from the specification table.

OCSET

(ΔI)

> I

+ ----------

OUT(MAX)

for

PEAK

where ΔI is the output inductor ripple current.

loads on the V

device, or other methods, the capacitance on the V

rail, through a voltage limiting protection

bus

For an equation for the ripple current see the section under

component guidelines titled “Output Inductor Selection” on

page 8.

will absorb the current. This situation will allow voltage level

of the V rail to increase. If the voltage level of the rail is

boosted to a level that exceeds the maximum voltage rating

of the ISL6520A, then the IC will experience an irreversible

failure and the converter will no longer be operational.

Ensuring that there is a path for the current to follow other

than the capacitance on the rail will prevent this failure

mode.

Soft-Start

The POR function initiates the soft-start sequence after the

overcurrent set point has been sampled. Soft-start clamps the

error amplifier output (COMP pin) and reference input

(non-inverting terminal of the error amp) to the internally

generated soft-start voltage. Figure 2 shows a typical start-up

interval where the COMP/OCSET pin has been released from

a grounded (system shutdown) state. Initially, the

Application Guidelines

Layout Considerations

COMP/OCSET is used to sample the overcurrent setpoint by

disabling the error amplifier and drawing 20µA through

As in any high frequency switching converter, layout is very

important. Switching current from one power device to another

can generate voltage transients across the impedances of the

interconnecting bond wires and circuit traces. These

interconnecting impedances should be minimized by using

wide, short printed circuit traces. The critical components

should be located as close together as possible, using ground

plane construction or single point grounding.

. Once the overcurrent level has been sampled, the

OCSET

soft-start function is initiated. The clamp on the error amplifier

(COMP/OCSET pin) initially controls the converter’s output

voltage during soft-start. The oscillator’s triangular waveform is

compared to the ramping error amplifier voltage. This

generates PHASE pulses of increasing width that charge the

output capacitor(s). When the internally generated soft-start

voltage exceeds the feedback (FB pin) voltage, the output

voltage is in regulation. This method provides a rapid and

FN9016.6

December 10, 2009

1...4 5 678 9 10...13

下载PDF

与ISL6520AIB相关器件

型号	品牌	描述	获取价格	数据表
ISL6520AIB-T	RENESAS	SWITCHING CONTROLLER, 340kHz SWITCHING FREQ-MAX, PDSO8, PLASTIC, MS-012-AA, SOIC-8	获取价格
ISL6520AIB-T	ROCHESTER	SWITCHING CONTROLLER, 340 kHz SWITCHING FREQ-MAX, PDSO8, PLASTIC, MS-012-AA, SOIC-8	获取价格
ISL6520AIBZ	INTERSIL	Single Synchronous Buck Pulse-Width Modulation (PWM) Controller	获取价格
ISL6520AIBZ	RENESAS	Single Synchronous Buck Pulse-Width Modulation (PWM) controller; SOIC8; Temp Range: See Da	获取价格
ISL6520AIBZ	ROCHESTER	SWITCHING CONTROLLER, 340 kHz SWITCHING FREQ-MAX, PDSO8, LEAD FREE, PLASTIC, MS-012-AA, SO	获取价格
ISL6520AIR	INTERSIL	Single Synchronous Buck Pulse-Width Modulation (PWM) Controller	获取价格

与ISL6520AIB相关文章

STM32H743技术深度剖析与应用案例探索
2024-05-30

17
LM321中文资料解析：引脚功能介绍、技术特点、技术特性分析
2024-05-30

16
74HC14芯片资料介绍：性能特性分析、引脚介绍
2024-05-30

14
LM1875芯片手册：功放参数分析、引脚说明、电路设计要点
2024-05-30

11

产品中心

服务支持

精选活动

关于我们

帮助中心

ISL6520AIB

ISL6520AIB 技术参数

ISL6520AIB 数据手册

与ISL6520AIB相关器件

与ISL6520AIB相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

ISL6520AIB

ISL6520AIB 技术参数

ISL6520AIB 数据手册

与ISL6520AIB相关器件

与ISL6520AIB相关文章

您还可以找

您在本页遇到什么问题？