5秒后页面跳转
INA101KU PDF预览

INA101KU

更新时间: 2024-01-31 12:41:10
品牌 Logo 应用领域
BB 仪表放大器放大器电路光电二极管
页数 文件大小 规格书
6页 94K
描述
High Accuracy INSTRUMENTATION AMPLIFIER

INA101KU 技术参数

是否Rohs认证: 不符合生命周期:Obsolete
包装说明:, CAN10,.23Reach Compliance Code:unknown
风险等级:5.7放大器类型:INSTRUMENTATION AMPLIFIER
JESD-30 代码:O-MBCY-W10JESD-609代码:e0
标称负供电电压 (Vsup):-15 V功能数量:1
端子数量:10最高工作温度:125 °C
最低工作温度:-55 °C封装主体材料:METAL
封装等效代码:CAN10,.23封装形状:ROUND
封装形式:CYLINDRICAL电源:+-15 V
子类别:Instrumentation Amplifiers最大压摆率:17 mA
标称供电电压 (Vsup):15 V技术:BIPOLAR
温度等级:MILITARY端子面层:Tin/Lead (Sn/Pb)
端子形式:WIRE端子位置:BOTTOM
Base Number Matches:1

INA101KU 数据手册

 浏览型号INA101KU的Datasheet PDF文件第1页浏览型号INA101KU的Datasheet PDF文件第2页浏览型号INA101KU的Datasheet PDF文件第3页浏览型号INA101KU的Datasheet PDF文件第4页浏览型号INA101KU的Datasheet PDF文件第6页 
TYPICAL PERFORMANCE CURVES (CONT)  
At +25°C, VCC = ±15V unless otherwise noted.  
OUTPUT NOISE vs GAIN  
SETTLING TIME vs GAIN  
1000  
100  
10  
30  
20  
10  
0
RL = 2kΩ  
L = 1000pF  
0.01%  
0.1%  
C
RS = 1MΩ  
RS = 1000kΩ  
RS = 10kΩ  
RS = 0  
1%  
0
10  
100  
1000  
1
10  
100  
1000  
Gain (V/V)  
Gain (V/V)  
INPUT NOISE VOLTAGE  
vs FREQUENCY (100 GAIN 1000)  
1000  
100  
10  
1
0
10  
100  
1000  
Frequency (Hz)  
APPLICATION INFORMATION  
Figure 1 shows the basic connections required for operation  
of the INA101. (Pin numbers shown are for the TO-100  
metal package.) Applications with noisy or high impedance  
power supplies may require decoupling capacitors close to  
the device pins as shown.  
The 40kterm in equation (1) comes from the sum of the  
two internal feedback resistors. These are on-chip metal film  
resistors which are laser trimmed to accurate absolute val-  
ues. The accuracy and temperature coefficient of these  
resistors are included in the gain accuracy and drift specifi-  
cations of the INA101.  
The output is referred to the output Common terminal which  
is normally grounded. This must be a low-impedance con-  
nection to assure good common-mode rejection. A resis-  
tance greater than 0.1in series with the Common pin will  
cause common-mode rejection to fall below 106dB.  
The stability and temperature drift of the external gain  
setting resistor, RG, also affects gain. RG’s contribution to  
gain accuracy and drift can be directly inferred from the gain  
equation (1). Low resistor values required for high gain can  
make wiring resistance important. Sockets add to the wiring  
resistance which will contribute additional gain error (possi-  
bly an unstable gain error) in gains of approximately 100 or  
greater. The gain sense connections on the DIP and SOL-16  
packages (see Figure 2) reduce the gain error produced by  
wiring or socket resistance.  
SETTING THE GAIN  
Gain of the INA101 is set by connecting a single external  
resistor, RG:  
40kΩ  
RG  
(1)  
G = 1 +  
®
5
INA101  

与INA101KU相关器件

型号 品牌 描述 获取价格 数据表
INA101KU/1K TI 极高精度仪表放大器 | DW | 16

获取价格

INA101KU-BI BB Instrumentation Amplifier, 1 Func, 1150uV Offset-Max, 0.3MHz Band Width, BIPolar, PDSO16,

获取价格

INA101SG BB High Accuracy INSTRUMENTATION AMPLIFIER

获取价格

INA101SG1 TI Very High Accuracy Instrumentation Amplifier 10-TO-100

获取价格

INA101SG-BI BB 暂无描述

获取价格

INA101SL-BS BB Instrumentation Amplifier, 1 Func, BIPolar, CQCC20,

获取价格