Datasheet > HY5DU113222FM-2

HY5DU113222FM-2

更新时间： 2024-02-09 15:42:24

品牌	Logo	应用领域
海力士 - HYNIX		动态存储器双倍数据速率
页数	文件大小	规格书
30页	295K
描述
512M(16Mx32) GDDR SDRAM

阅读下载

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

HY5DU113222FM-2 技术参数

是否Rohs认证：	不符合	生命周期：	Obsolete
零件包装代码：	BGA	包装说明：	LFBGA, BGA144,12X12,32
针数：	144	Reach Compliance Code：	unknown
ECCN代码：	EAR99	HTS代码：	8542.32.00.28
风险等级：	5.92	访问模式：	FOUR BANK PAGE BURST
最长访问时间：	0.6 ns	其他特性：	AUTO/SELF REFRESH
最大时钟频率 (fCLK)：	500 MHz	I/O 类型：	COMMON
交错的突发长度：	2,4,8	JESD-30 代码：	S-PBGA-B144
长度：	12 mm	内存密度：	536870912 bit
内存集成电路类型：	DDR DRAM	内存宽度：	32
功能数量：	1	端口数量：	1
端子数量：	144	字数：	16777216 words
字数代码：	16000000	工作模式：	SYNCHRONOUS
最高工作温度：	70 °C	最低工作温度：
组织：	16MX32	输出特性：	3-STATE
封装主体材料：	PLASTIC/EPOXY	封装代码：	LFBGA
封装等效代码：	BGA144,12X12,32	封装形状：	SQUARE
封装形式：	GRID ARRAY, LOW PROFILE, FINE PITCH	峰值回流温度（摄氏度）：	NOT SPECIFIED
电源：	2.5 V	认证状态：	Not Qualified
刷新周期：	4096	座面最大高度：	1.3 mm
自我刷新：	YES	连续突发长度：	2,4,8
最大待机电流：	0.1 A	子类别：	DRAMs
最大压摆率：	1.44 mA	最大供电电压 (Vsup)：	2.7 V
最小供电电压 (Vsup)：	2.375 V	标称供电电压 (Vsup)：	2.5 V
表面贴装：	YES	技术：	CMOS
温度等级：	COMMERCIAL	端子形式：	BALL
端子节距：	0.8 mm	端子位置：	BOTTOM
处于峰值回流温度下的最长时间：	NOT SPECIFIED	宽度：	12 mm
Base Number Matches：	1

HY5DU113222FM-2 数据手册

HY5DU113222FM(P)

PIN DESCRIPTION

TYPE

DESCRIPTION

Clock: CK and /CK are differential clock inputs. All address and control input signals are

sampled on the crossing of the positive edge of CK and negative edge of /CK. Output

(read) data is referenced to the crossings of CK and /CK (both directions of crossing).

CK, /CK

Input

Clock Enable: CKE HIGH activates, and CKE LOW deactivates internal clock signals, and

device input buffers and output drivers. Taking CKE LOW provides PRECHARGE POWER

DOWN and SELF REFRESH operation (all banks idle), or ACTIVE POWER DOWN (row

ACTIVE in any bank). CKE is synchronous for POWER DOWN entry and exit, and for SELF

REFRESH entry. CKE is asynchronous for SELF REFRESH exit, and for output disable. CKE

must be maintained high throughout READ and WRITE accesses. Input buffers, excluding

CK, /CK and CKE are disabled during POWER DOWN. Input buffers, excluding CKE are

disabled during SELF REFRESH. CKE is an SSTL_2 input, but will detect an LVCMOS LOW

level after Vdd is applied.

CKE

Input

Chip Select : Enables or disables all inputs except CK, /CK, CKE, DQS and DM. All com-

mands are masked when CS0 or CS1 is registered high. CS0 or CS1 provides for external

bank selection on systems with multiple banks. CS0 and CS1 are considered part of the

command code. When it is the operationg state of MRS, Power up sequence, EMRS, it

should be enabled in pairs. Except this case, it can be operated, individually.

/CS0, /CS1

BA0, BA1

Input

Bank Address Inputs: BA0 and BA1 define to which bank an ACTIVE, Read, Write or PRE-

CHARGE command is being applied.

Address Inputs: Provide the row address for ACTIVE commands, and the column address

and AUTO PRECHARGE bit for READ/WRITE commands, to select one location out of the

memory array in the respective bank. A8 is sampled during a precharge command to

determine whether the PRECHARGE applies to one bank (A8 LOW) or all banks (A8

HIGH). If only one bank is to be precharged, the bank is selected by BA0, BA1. The

address inputs also provide the op code during a MODE REGISTER SET command. BA0

and BA1 define which mode register is loaded during the MODE REGISTER SET command

(MRS or EMRS).

A0 ~ A11

Input

Command Inputs: /RAS, /CAS and /WE (along with /CS) define the command being

entered.

/RAS, /CAS, /WE

DM0 ~ DM3

Input

Input Data Mask: DM(0~3) is an input mask signal for write data. Input data is masked

when DM is sampled HIGH along with that input data during a WRITE access. DM is sam-

pled on both edges of DQS. Although DM pins are input only, the DM loading matches the

DQ and DQS loading. DM0 corresponds to the data on DQ0-Q7; DM1 corresponds to the

data on DQ8-Q15; DM2 corresponds to the data on DQ16-Q23; DM3 corresponds to the

data on DQ24-Q31.

Data Strobe: Output with read data, input with write data. Edge aligned with read data,

centered in write data. Used to capture write data. DQS0 corresponds to the data on

DQ0-Q7; DQS1 corresponds to the data on DQ8-Q15; DQS2 corresponds to the data on

DQ16-Q23; DQS3 corresponds to the data on DQ24-Q31

D Q S 0 ~ D Q S 3

I / O

DQ0 ~ DQ31

VDD/VSS

VDDQ/VSSQ

VREF

I/O

Data input / output pin : Data Bus

Supply

Power supply for internal circuits and input buffers.

Power supply for output buffers for noise immunity.

Reference voltage for inputs for SSTL interface.

No connection.

Rev. 0.1 / Oct. 2004

1 2 3 456 7 8...30

下载PDF

与HY5DU113222FM-2相关器件

型号	品牌	描述	获取价格	数据表
HY5DU113222FM-22	HYNIX	512M(16Mx32) GDDR SDRAM	获取价格
HY5DU113222FM-25	HYNIX	512M(16Mx32) GDDR SDRAM	获取价格
HY5DU113222FM-28	HYNIX	512M(16Mx32) GDDR SDRAM	获取价格
HY5DU113222FM-33	HYNIX	512M(16Mx32) GDDR SDRAM	获取价格
HY5DU113222FM-36	HYNIX	512M(16Mx32) GDDR SDRAM	获取价格
HY5DU113222FM-4	HYNIX	512M(16Mx32) GDDR SDRAM	获取价格

与HY5DU113222FM-2相关文章

PCF8574资料解读：主要参数分析、引脚说明
2024-05-21

5
AD637数据手册解读：主要特性、引脚及其功能解读、电气参数
2024-05-21

4
ADUM1201资料手册解读：参数分析、引脚说明、应用分析
2024-05-21

7
一文带你了解压敏电阻器在直流电路中的过压保护作用
2024-05-21

3

产品中心

服务支持

精选活动

关于我们

帮助中心

HY5DU113222FM-2

HY5DU113222FM-2 技术参数

HY5DU113222FM-2 数据手册

与HY5DU113222FM-2相关器件

与HY5DU113222FM-2相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

HY5DU113222FM-2

HY5DU113222FM-2 技术参数

HY5DU113222FM-2 数据手册

与HY5DU113222FM-2相关器件

与HY5DU113222FM-2相关文章

您还可以找

您在本页遇到什么问题？