5秒后页面跳转
HFBR-ELD15D PDF预览

HFBR-ELD15D

更新时间: 2024-01-27 02:40:08
品牌 Logo 应用领域
富士康 - FOXCONN /
页数 文件大小 规格书
10页 251K
描述
Interconnection Device

HFBR-ELD15D 技术参数

生命周期:ActiveReach Compliance Code:unknown
风险等级:5.57Is Samacsys:N
连接器类型:INTERCONNECTION DEVICEBase Number Matches:1

HFBR-ELD15D 数据手册

 浏览型号HFBR-ELD15D的Datasheet PDF文件第3页浏览型号HFBR-ELD15D的Datasheet PDF文件第4页浏览型号HFBR-ELD15D的Datasheet PDF文件第5页浏览型号HFBR-ELD15D的Datasheet PDF文件第7页浏览型号HFBR-ELD15D的Datasheet PDF文件第8页浏览型号HFBR-ELD15D的Datasheet PDF文件第9页 
Step 4  
Placeꢀtheꢀflushꢀconnectorꢀandꢀpolishingꢀfixtureꢀonꢀtheꢀdullꢀ  
sideꢀofꢀtheꢀ3ꢀµmꢀpinkꢀlappingꢀfilmꢀandꢀcontinueꢀtoꢀpolishꢀ  
theꢀfiberꢀandꢀconnectorꢀforꢀapproximatelyꢀ25ꢀstrokes.Theꢀ  
fiberꢀendꢀshouldꢀbeꢀflat,ꢀsmoothꢀandꢀclean.  
Step 3  
Thisꢀcableꢀisꢀnowꢀreadyꢀforꢀuse.  
Anyꢀexcessꢀfiberꢀprotrudingꢀfromꢀtheꢀconnectorꢀendꢀmayꢀ  
beꢀcutꢀoff;ꢀhowever,ꢀtheꢀtrimmedꢀfiberꢀshouldꢀextendꢀatꢀ  
leastꢀ1.5ꢀmmꢀ(0.06ꢀin)ꢀfromꢀtheꢀconnectorꢀend.  
Note:Useofthepinklappinglmnepolishingstepresultsin  
approximately 2 dB improvement in coupling performance  
of either a transmitter­receiver link or a bulkhead/splice over  
a 600 grit polish alone. This fine polish is comparable to the  
Avago factory polish. The fine polishing step may be omitted  
where an extra 2 dB of optical power is not essential, as with  
shortlinklengths. Properpolishingofthetipoftheber/con­  
nector face results in a tip diameter between 2.5 mm (0.098  
in.) minimum and 3.2 mm (0.126 in.) maximum..  
Insertꢀtheꢀconnectorꢀfullyꢀintoꢀtheꢀpolishingꢀfixtureꢀwithꢀ  
theꢀ trimmedꢀ fiberꢀ protrudingꢀ fromꢀ theꢀ bottomꢀ ofꢀ theꢀ  
fixture.Thisꢀplasticꢀpolishingꢀfixtureꢀcanꢀbeꢀusedꢀtoꢀpolishꢀ  
twoꢀsimplexꢀconnectorsꢀorꢀsimplexꢀlatchingꢀconnectorsꢀ  
simultaneously,ꢀorꢀoneꢀduplexꢀconnector.  
Note: The four dots on the bottom of the polishing fixture  
are wear indicators. Replace the polishing fixture when any  
dot is no longer visible. Typically, the polishing fixture can  
be used 10 times; 10 duplex connectors or 20 simplex con­  
nectors, two at a time.  
HFBR-4593 Polishing Kit  
Place the 600 grit abrasive paper on a flat smooth surface,  
pressing down on the connector, polish the fiber and the  
connector using a figure eight pattern of strokes until the  
connector is flush with the bottom of the polishing fixture.  
Wipe the connector and fixture with a clean cloth or tissue.  
6

与HFBR-ELD15D相关器件

型号 品牌 描述 获取价格 数据表
HFBR-ELD500Z AVAGO Plastic Optical Fiber Cable and Accessories for Versatile Link

获取价格

HFBR-ELS015 FOXCONN INTERCONNECTION DEVICE

获取价格

HFBR-ELS015 AGILENT Plastic Optical Fiber Cable and Accessories for Versatile Link

获取价格

HFBR-ELS015Z AVAGO INTERCONNECTION DEVICE, ROHS COMPLIANT

获取价格

HFBR-ELS100Z AVAGO Plastic Optical Fiber Cable and Accessories for Versatile Link

获取价格

HFBR-ELS15D AGILENT Plastic Optical Fiber Cable and Accessories for Versatile Link

获取价格