Datasheet > GS8342D06BD-500I

GS8342D06BD-500I

更新时间： 2022-12-29 21:03:14

品牌	Logo	应用领域
GSI		/
页数	文件大小	规格书
30页	523K
描述
JEDEC-standard pinout and package

阅读下载

获取价格

如果您发现信息不准确，欢迎纠错

GS8342D06BD-500I 数据手册

GS8342D06/11/20/38BD-550/500/450/400/350

Background

Separate I/O SRAMs, from a system architecture point of view, are attractive in applications where alternating reads and writes are

needed. Therefore, the SigmaQuad-II+ SRAM interface and truth table are optimized for alternating reads and writes. Separate I/O

SRAMs are unpopular in applications where multiple reads or multiple writes are needed because burst read or write transfers from

Separate I/O SRAMs can cut the RAM’s bandwidth in half.

SigmaQuad-II+ B4 SRAM DDR Read

The status of the Address Input, W, and R pins are sampled by the rising edges of K. W and R high causes chip disable. A Low on

the Read Enable pin, R, begins a read cycle. R is always ignored if the previous command loaded was a read command. Clocking

in a High on the Read Enable pin, R, begins a read port deselect cycle.

SigmaQuad-II+ B4 SRAM DDR Write

The status of the Address Input, W, and R pins are sampled by the rising edges of K. W and R High causes chip disable. A Low on

the Write Enable pin, W, and a High on the Read Enable pin, R, begins a write cycle. W is always ignored if the previous command

was a write command. Data is clocked in by the next rising edge of K, the rising edge of K after that, the next rising edge of K, and

finally by the next rising edge of K.

Special Functions

Byte Write and Nybble Write Control

Byte Write Enable pins are sampled at the same time that Data In is sampled. A High on the Byte Write Enable pin associated with

a particular byte (e.g., BW0 controls D0–D8 inputs) will inhibit the storage of that particular byte, leaving whatever data may be

stored at the current address at that byte location undisturbed. Any or all of the Byte Write Enable pins may be driven High or Low

during the data in sample times in a write sequence.

Each write enable command and write address loaded into the RAM provides the base address for a 4-beat data transfer. The x18

version of the RAM, for example, may write 72 bits in association with each address loaded. Any 9-bit byte may be masked in any

write sequence.

Nybble Write (4-bit) control is implemented on the 8-bit-wide version of the device. For the x8 version of the device, “Nybble

Write Enable” and “NWx” may be substituted in all the discussion above.

Rev: 1.02c 8/2017

7/30

Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.

1...4 5 678 9 10...30

下载PDF

型号	品牌	描述	获取价格	数据表
GS8342D06BD-550	GSI	165 BGA	获取价格
GS8342D06BD-550I	GSI	2.5 Clock Latency	获取价格
GS8342D06BGD-350	GSI	JEDEC-standard pinout and package	获取价格
GS8342D06BGD-350I	GSI	JEDEC-standard pinout and package	获取价格
GS8342D06BGD-400	GSI	JEDEC-standard pinout and package	获取价格
GS8342D06BGD-400I	GSI	JEDEC-standard pinout and package	获取价格