■ Specifications and Test Methods
No Item
10 Mechanical Shock
Specification
Test Method(Ref. Standard:AEC-Q200)
Solder the capacitor on the test substrate
Half-sine
1500g
Appearance
Capacitance
Q or D.F.
No defects or abnormalities.
Within the specified initial value.
Within the specified initial value.
More than 10000MΩ
Mounting method
Waveform
Peak value
I.R.(Room Temp.)
Holding Time
0.5ms
Velocity change
Shocks directions and times
4.7m/s
Three shocks in each direction should be applied along 3
mutually perpendicular axes of the test specimen (18 shocks).
Appearance
Capacitance
Q or D.F.
No defects or abnormalities.
Within the specified initial value.
Within the specified initial value.
More than 10000MΩ
Mounting method
Kind of Vibration
Vibration Time
Solder the capacitor on the test substrate
A 10Hz to 2000Hz to 10Hz
20min
1.5mm
11 Vibration
I.R.(Room Temp.)
Total amplitude
Vibration directions and time
This motion should be applied for 12 items in each 3 mutually perpendicular directions
(total of 36 times).
Appearance
Capacitance or Capacitance Change
No defects or abnormalities.
Capacitance Change:Within +/-0.25pF
Within the specified initial value.
More than 10000MΩ
Test Method
Solder bath method
Sn-3.0Ag-0.5Cu(Lead Free Solder)
260+/-5℃
10+/-1s
12 Resistance to Soldering
Heat
Kind of Solder
Test Temperature
Test Time
Q or D.F.
I.R.(Room Temp.)
Post-treatment
Non treatment:Let sit for 24+/-2hours at room temperature, then measure.
Appearance
Capacitance
Q or D.F.
No defects or abnormalities.
Within the specified initial value.
Within the specified initial value.
More than 10000MΩ
Per AEC-Q200-002
13 ESD
I.R.(Room Temp.)
95% of the terminations is to be soldered evenly and continuously.
Pre-treatment
Flux
Kind of Solder
Solder Temperature
Immersion time
Immersion and emersion rate
Perform a heat treatment at 155°C for 4hours.
Solution of rosin ethanol 25(mass)%
Sn-3.0Ag-0.5Cu(Lead Free Solder)
Sn-3.0Ag-0.5Cu solder solution at 245+/-5 ℃
5+0/-0.5s
14 Solderability (a)
25+/-5mm/s
Measurement Temperature
Shown in Rated value.
25℃
15 Capacitance
Measurement Frequency 1.0+/-0.1MHz
Measurement Voltage
0.5 to 5.0Vrms
Measurement Temperature
Q≧400+20C C:Nominal Capacitance(pF)
More than 100000MΩ
25℃
16 Q or Dissipation Factor
(D.F.)
Measurement Frequency 1.0+/-0.1MHz
Measurement Voltage
0.5 to 5.0Vrms
Measurement Temperature
Measurement Voltage
Charging Time
25℃
Rated Voltage
1min
17 Insulation
Resistance(I.R.)
(Room Temperature)
Charge/discharge current 50mA max.
Measurement Temperature
Measurement Voltage
Charging Time
More than 10000MΩ
125℃
Rated Voltage
1min
18 Insulation
Resistance(I.R.)
(High Temperature)
Charge/discharge current 50mA max.
GRT0335C1HR82BA02-01A
3