■AEC-Q200 Murata Standard Specification and Test Methods
No
7
Specification.
AEC-Q200 Test Method
AEC-Q200 Test Item
Operational Life
The measured and observed characteristics should satisfy the
specifications in the following table.
Solder the capacitor on the test substrate(glass epoxy board).
Apply 150% of the rated voltage for 1000+/-12h at 125+/-3℃.
The charge/discharge current is less than 50mA.
Appearance
No marking defects
Set for 24+/-2h at room temperature, then measure.
Capacitance
Change
D.F.
Within +/-10.0%
・Initial measurement
Within the specified initial value.
Apply the test voltage at the max. operating temp. +/-3°C for 1h
and then let sit for 24+/-2h at room temperature,then measure.
I.R.ꢀ25℃
External Visual
More than 1,000MΩ or 50Ω・F
(Whichever is smaller)
8
9
No defects or abnormalities
Visual inspection
Physical Dimension
Within the specified dimensions
No marking defects
Using Measuring instrument of dimension.
10 Resistance to Appearance
Solvents
Per MIL-STD-202 Method 215
Solvent 1 : 1 part (by volume) of isopropyl alcohol
3 parts (by volume) of mineral spirits
Solvent 2 : Terpene defluxer
Capacitance
Within the specified initial value.
Within the specified initial value.
Within the specified initial value.
D.F.
Solvent 3 : 42 parts (by volume) of water
1part (by volume) of propylene glycol monomethyl ether
1 part (by volume) of monoethanolomine
I.R.ꢀ25℃
11 Mechanical
Shock
Appearance
Capacitance
D.F.
No marking defects
Solder the capacitor on the test substrate(glass epoxy board).
Three shocks in each direction should be applied along 3 mutually
perpendicular axes of the test specimen (18 shocks).
Within the specified initial value.
Within the specified initial value.
Within the specified initial value.
No marking defects
The specified test pulse should be Half-sine and should have a
duration :0.5ms, peak value:1500g and velocity change: 4.7m/s.
I.R.ꢀ25℃
Appearance
Capacitance
D.F.
12 Vibration
Solder the capacitor on the test substrate(glass epoxy board).
The capacitor should be subjected to a simple harmonic motion having
a total amplitude of 1.5mm, the frequency being varied uniformly
between the approximate limits of 10 and 2000Hz.
Within the specified initial value.
Within the specified initial value.
Within the specified initial value.
The frequency range, from 10 to 2000Hz and return to 10Hz,
should be traversed in approximately 20 minutes.
I.R.ꢀ25℃
This motion should be applied for 12 items in each 3 mutually
perpendicular directions (total of 36 times).
13 Resistance to
Soldering Heat
The measured and observed characteristics should satisfy the
specifications in the following table.
Immerse the capacitor in Sn-3.0Ag-0.5Cu solder solution or an eutectic
solder solution at 260+/-5℃ for 10+/-1s.
Appearance
No marking defects
・ Initial measurement
Capacitance
D.F.
Within the specified initial value.
Within the specified initial value.
Within the specified initial value.
Perform a heat treatment at 150+0/-10 ℃for 1h and then sit
for 24+/-2h at room temperature.
Perform the initial measurement.
I.R.ꢀ25℃
JEMCGS-02082A
3
5秒后页面跳转
高性能TDA7293音频功率放大器技术特性与应用分析
STM32H743技术深度剖析与应用案例探索
LM321中文资料解析：引脚功能介绍、技术特点、技术特性分析
74HC14芯片资料介绍：性能特性分析、引脚介绍
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
