Model Selection Guide
Input
Output
Voltage Current
(VDC) (mA, Max) (mA, Min)
Load
Regulation
(%, Max)
Fuse Rating
Slow-Blow
(mA)
Model
Efficiency
(%, Typ)
Voltage (VDC)
Number
Current (mA)
Full-Load No-Load
Current
Nominal
5
Range
G201EI
G202EI
G203EI
G204EI
G205EI
G206EI
G207EI
G208EI
G211EI
G212EI
G213EI
G214EI
G215EI
G216EI
G217EI
G218EI
G221EI
G222EI
G223EI
G224EI
G225EI
G226EI
G227EI
G228EI
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
500
494
488
476
488
482
470
470
208
201
198
196
201
198
194
194
103
99
30
30
30
30
30
30
30
30
15
15
15
15
15
15
15
15
8
8
8
8
8
8
8
8
5.0
9.0
12.0
15.0
5.0
400.0
222.0
167.0
133.0
200.0
111.0
83.0
40.0
23.0
17.0
14.0
20.0
12.0
9.0
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
80
81
82
84
82
83
85
85
80
83
84
85
83
84
86
86
81
84
85
86
84
85
87
87
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
500
500
500
500
500
500
500
500
250
250
250
250
250
5
5
5
5
5
5
5
12
12
12
12
12
12
12
12
24
24
24
24
24
24
24
24
9.0
12.0
15.0
5.0
67.0
7.0
400.0
222.0
167.0
133.0
200.0
111.0
83.0
40.0
23.0
17.0
14.0
20.0
12.0
9.0
9.0
12.0
15.0
5.0
9.0
12.0
15.0
5.0
67.0
7.0
400.0
222.0
167.0
133.0
200.0
111.0
83.0
40.0
23.0
17.0
14.0
20.0
12.0
9.0
9.0
98
97
99
98
96
96
12.0
15.0
5.0
9.0
12.0
15.0
250
250
250
67.0
7.0
Notes:
Derating Curve
1. Output load regulation is specified for a load change of 10% to
100%.
2. These units should not be operated with a load under 10% of
full load. Operation at no-load may cause damage to the unit.
3. These converters will operate without external components.
However, when measuring output ripple, it is recommended
that an external ceramic capacitor be placed from the +Vout
pin to the -Vout pin for single output units and from each out-
put to common for dual output units. An input capacitor will
enhance stability over temperature and input line variations.
Recommended capacitor values are given in the table below.
For applications requiring very low output noise levels, a simple
LC filter should be effective.
Output Capacitor
Single Dual
5 VDC 10.0 μF 4.7 μF
Input
Capacitor
Vin
Vout
5 VDC
12 VDC
24 VDC
4.7 μF
2.2 μF
1.0 μF
9 VDC
4.7 μF
2.2 μF
1.0 μF
Mechanical Dimensions
12 VDC 2.2 μF
15 VDC 1.0 μF 0.47 μF
4. Dual output units may be connected to provide a 10V, 18V, 24V
or 30 VDC output. To do this, connect the load across the posi-
tive (+Vout) and negative (-Vout) outputs and float the output
common
5. It is recommended that a fuse be used on the input of a power
supply for protection. See the Model Selection table above for
the correct rating.
Pin Connections
Pin Single
Dual
Pin
Single
Dual
1
7
8
-Vin
NC
-Vin
NC
9
No Pin Common
10
14
-Vout
+Vin
-Vout
+Vin
+Vout +Vout
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = 0.01 ( 0.25)
• Pin 1 is marked by a “dot” or indentation on the top of the unit
MicroPower Direct
•
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
FAX: (781) 344-8481
•
E-Mail: sales@micropowerdirect.com