Model Selection Guide
Input
Output
Voltage Current
(VDC) (mA, Max) (mA, Min)
Load
Regulation
(%, Max)
Fuse Rating
Slow-Blow
(mA)
Model
Efficiency
(%, Typ)
Voltage (VDC)
Number
Current (mA)
Full-Load No-Load
Current
Nominal
5
Range
G201E
G202E
G203E
G204E
G205E
G206E
G207E
G208E
G211E
G212E
G213E
G214E
G215E
G216E
G217E
G218E
G221E
G222E
G223E
G224E
G225E
G226E
G227E
G228E
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
494
488
476
476
488
482
470
470
203
201
196
196
201
198
194
194
100
99
30
30
30
30
30
30
30
30
15
15
15
15
15
15
15
15
8
8
8
8
8
8
8
8
5.0
9.0
12.0
15.0
5.0
400.0
222.0
167.0
133.0
200.0
111.0
83.0
40.0
23.0
17.0
14.0
20.0
12.0
9.0
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
81
82
84
84
82
83
85
85
82
83
85
85
83
84
86
86
83
84
86
86
84
85
87
87
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
500
500
500
500
500
500
500
500
250
250
250
250
250
5
5
5
5
5
5
5
12
12
12
12
12
12
12
12
24
24
24
24
24
24
24
24
9.0
12.0
15.0
5.0
67.0
7.0
400.0
222.0
167.0
133.0
200.0
111.0
83.0
40.0
23.0
17.0
14.0
20.0
12.0
9.0
9.0
12.0
15.0
5.0
9.0
12.0
15.0
5.0
67.0
7.0
400.0
222.0
167.0
133.0
200.0
111.0
83.0
40.0
23.0
17.0
14.0
20.0
12.0
9.0
9.0
97
97
99
98
96
96
12.0
15.0
5.0
9.0
12.0
15.0
250
250
250
67.0
7.0
Notes:
Derating Curve
1. Output load regulation is specified for a load change of 10% to
100%.
2. These units should not be operated with a load under 10% of
full load. Operation at no-load may cause damage to the unit.
3. These converters will operate without external components.
However, when measuring output ripple, it is recommended
that an external ceramic capacitor be placed from the +Vout
pin to the -Vout pin for single output units and from each out-
put to common for dual output units. An input capacitor will
enhance stability over temperature and input line variations.
Recommended capacitor values are given in the table below.
For applications requiring very low output noise levels, a simple
LC filter should be effective.
Output Capacitor
Single Dual
5 VDC 10.0 µF 4.7 µF
Input
Capacitor
Vin
Vout
5 VDC
12 VDC
24 VDC
4.7 µF
2.2 µF
1.0 µF
9 VDC
4.7 µF
2.2 µF
1.0 µF
Mechanical Dimensions
12 VDC 2.2 µF
15 VDC 1.0 µF 0.47 µF
4. Dual output units may be connected to provide a 10V, 18V, 24V
or 30 VDC output. To do this, connect the load across the posi-
tive (+Vout) and negative (-Vout) outputs and float the output
common
5. It is recommended that a fuse be used on the input of a power
supply for protection. See the Model Selection table above for
the correct rating.
Pin Connections
Pin
Single
Dual
Pin
Single
Dual
1
7
8
-Vin
NC
-Vin
NC
9
+Vout
No Pin
+Vin
+Vout
-Vout
+Vin
11
14
-Vout
Common
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = 0.01 ( 0.25)
• Pin 1 is marked by a “dot” or indentation on the top of the unit
MicroPower Direct
•
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
FAX: (781) 344-8481
•
E-Mail: sales@micropowerdirect.com
5秒后页面跳转
STM32H743技术深度剖析与应用案例探索
LM321中文资料解析：引脚功能介绍、技术特点、技术特性分析
74HC14芯片资料介绍：性能特性分析、引脚介绍
LM1875芯片手册：功放参数分析、引脚说明、电路设计要点
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
