Amplifier Built-in
Ultra-compact Photoelectric Sensor
293
EX-20 SERIES Ver.2
■General terms and conditions............. F-3
■Selection guide............................. P.231~
■Korea’s S-mark……………........... P.1602
FIBER
SENSORS
Related Information
■
Glossary of terms / General precautions . P.1549~ / P.1552~
LASER
SENSORS
PHOTOELECTRIC
SENSORS
Ver.2
Recognition
(Excluding 5 m cable length type)
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
Certified
(Some models only)
SAFETY LIGHT
CURTAINS /
SAFETY COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
panasonic.net/id/pidsx/global
PNP output
type available
STATIC
CONTROL
DEVICES
LASER
MARKERS
Miniature-sized and still mountable with M3 screws
PLC
HUMAN MACHINE
INTERFACES
Miniaturization by using single chip optical IC Incorporates a sensitivity adjuster even in this size
ENERGY
MANAGEMENT
SOLUTIONS
The beam-receiving photodiode and
the A/D conversion circuit have been
fabricated on a single chip optical IC
(full custom). Hence, in spite of its
miniature size, it has a performance
and reliability which is equal to or
better than the conventional product.
The sensor incorporates a sensitivity
adjuster in spite of its miniature size.
It is convenient when you need fine
adjustment. Further, the receiver of the
thru-beam, side sensing type sensor
incorporates an operation mode switch
which can change the output operation.
8.2 mm
0.323 in
10.5 mm
0.413 in
FA COMPONENTS
19 mm
0.748 in
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
BASIC PERFORMANCE
Long sensing range
Clear beam spot using red LED dot light source
Selection
Guide
Amplifier
The EX-20 series achieves long distance sensing [thru-beam
type: 2 m 6.562 ft, retroreflective type: 200 mm 7.874 in (when
using the attached reflector), diffuse reflective type: 160 mm
6.299 in], despite its miniature size.
The emission area of a dot light source is smaller than that
of a conventional LED flat light source, and it is possible to
design a high power, narrow beam. Since a red LED dot
light source is used, the red beam spot is clear even at a far
place, so that alignment and confirmation of sensing position
is easy. Further, since the thru-beam type, too, incorporates
a visible narrow beam, it can also reliably detect small parts,
such as, chip components, lead frames, etc.
Built-in
Power Supply
Built-in
Amplifier-
separated
Hence, it is usable even on a wide conveyor.
EX-Z
CX-400
CY-100
EX-10
Thru-beam type
2 m 6.562 ft
EX-28□
EX-20
Retroreflective type
EX-30
EX-40
200 mm
7.874 in
Setting
CX-440
EQ-30
distance:
80 mm
3.150 in
ø5 mm
EX-26□
ø0.197 in
spot
EQ-500
MQ-W
Diffuse reflective type
ø1 mm
Setting
ø0.039 in
spot
distance:
10 mm
RX-LS200
RX
160 mm
6.299 in
0.394 in
RT-610
5秒后页面跳转
深入解析CS8416引脚说明、参数、技术特点
TPA3116D2功放芯片参数详解、引脚说明
移位寄存器74HC165引脚说明、驱动程序示例解读
深入解析AD9833：DDS频率合成器的卓越性能与广泛应用
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
