RoHS
Pb
EN13C7F2H-100.000M
EN13C7 F 2 H -100.000M
Series
Nominal Frequency
RoHS Compliant (Pb-free) 3.3V 6 Pad 5mm x 7mm
Ceramic SMD HCSL Oscillator
100.000MHz
Logic Control / Additional Output
Tri-State (Pad 2) and Complementary Output
Frequency Tolerance/Stability
±20ppm Maximum over 0°C to +70°C
Duty Cycle
50 ±5(%)
ELECTRICAL SPECIFICATIONS
Nominal Frequency
100.000MHz
Frequency Tolerance/Stability
±20ppm Maximum over 0°C to +70°C (Inclusive of all conditions: Calibration Tolerance (at 25°C),
Frequency Stability over the Operating Temperature Range, Supply Voltage Change, Output Load Change,
First Year Aging at 25°C, Shock, and Vibration)
Supply Voltage
+3.3Vdc ±5%
Input Current
35mA Typical, 60mA Maximum (Without Load)
700mVdc Typical, 600mVdc Minimum
20mVdc Typical, 50mVdc Maximum
300pSec Typical, 700pSec Maximum (Measured at 0.175Vdc to 0.525Vdc of waveform)
50 ±5(%) (Measured at the crossing point)
50 Ohms (Between Output and Ground)
HCSL
Output Voltage Logic High (Voh)
Output Voltage Logic Low (Vol)
Rise/Fall Time
Duty Cycle
Load Drive Capability
Output Logic Type
Phase Noise
-78dBc/Hz at 10Hz Offset, -113dBc/Hz at 100Hz Offset, -126dBc/Hz at 1kHz Offset, -134dBc/Hz at 10kHz
Offset, -140dBc/Hz at 100kHz Offset, -146dBc/Hz at 1MHz Offset, -148dBc/Hz at 10MHz Offset, -
152dBc/Hz at 20MHz Offset (All Values are Typical, Fo=100.000MHz)
Logic Control / Additional Output
Tri-State Input Voltage (Vih and Vil)
Tri-State (Pad 2) and Complementary Output
Vih of 70% of Vdd Minimum or No Connect to Enable Output and Complementary Output, Vil of 30% of
Vdd Maximum to Disable (High Impedance) Output and Complementary Output
Standby Current
RMS Phase Jitter
10µA Maximum (Without Load)
0.5pSec Typical, 0.6pSec Maximum at 100MHz; 0.4pSec Typical, 0.5pSec Maximum at 125MHz (Fj=12kHz
to 20MHz)
Period Jitter (Deterministic)
Period Jitter (Random)
Period Jitter (One Sigma)
Period Jitter (Cycle to Cycle)
Period Jitter (tp-p)
0.2pSec Typical
1.0pSec Typical
1.5pSec Typical
10pSec Typical
12pSec Typical
5mSec Maximum
-55°C to +125°C
Start Up Time
Storage Temperature Range
ENVIRONMENTAL & MECHANICAL SPECIFICATIONS
ESD Susceptibility
MIL-STD-883, Method 3015, Class 1, HBM: 1500V
MIL-STD-883, Method 1014, Condition A
UL94-V0
Fine Leak Test
Flammability
Gross Leak Test
Mechanical Shock
Moisture Resistance
Moisture Sensitivity
Resistance to Soldering Heat
Resistance to Solvents
Solderability
MIL-STD-883, Method 1014, Condition C
MIL-STD-883, Method 2002, Condition B
MIL-STD-883, Method 1004
J-STD-020, MSL 1
MIL-STD-202, Method 210, Condition K
MIL-STD-202, Method 215
MIL-STD-883, Method 2003
Temperature Cycling
Vibration
MIL-STD-883, Method 1010, Condition B
MIL-STD-883, Method 2007, Condition A
www.ecliptek.com | Specification Subject to Change Without Notice | Rev B 8/12/2010 | Page 1 of 5