5秒后页面跳转
EM6580SO8A+ PDF预览

EM6580SO8A+

更新时间: 2024-01-02 14:28:43
品牌 Logo 应用领域
EMMICRO 微控制器光电二极管
页数 文件大小 规格书
55页 1796K
描述
Ultra Low Power 8-pin Flash Microcontroller

EM6580SO8A+ 技术参数

是否Rohs认证: 符合生命周期:Contact Manufacturer
零件包装代码:SOIC包装说明:SOP, SOP8,.25
针数:8Reach Compliance Code:unknown
风险等级:5.8位大小:4
JESD-30 代码:R-PDSO-G8端子数量:8
最高工作温度:85 °C最低工作温度:-20 °C
封装主体材料:PLASTIC/EPOXY封装代码:SOP
封装等效代码:SOP8,.25封装形状:RECTANGULAR
封装形式:SMALL OUTLINE电源:2.5/5 V
认证状态:Not QualifiedRAM(字节):40
ROM(单词):4096ROM可编程性:FLASH
速度:0.8 MHz子类别:Microcontrollers
最大压摆率:0.1 mA表面贴装:YES
技术:CMOS温度等级:OTHER
端子形式:GULL WING端子节距:1.27 mm
端子位置:DUALBase Number Matches:1

EM6580SO8A+ 数据手册

 浏览型号EM6580SO8A+的Datasheet PDF文件第2页浏览型号EM6580SO8A+的Datasheet PDF文件第3页浏览型号EM6580SO8A+的Datasheet PDF文件第4页浏览型号EM6580SO8A+的Datasheet PDF文件第6页浏览型号EM6580SO8A+的Datasheet PDF文件第7页浏览型号EM6580SO8A+的Datasheet PDF文件第8页 
R
EM6580  
2. Operating modes  
The EM6580 can operate in three different modes of which 2 are low-power dissipation modes (Stand-By and  
Sleep). The modes and transitions between them are shown in Figure 5.  
1.) Active mode  
2.) Stand-By mode  
3.) Sleep mode  
Figure 4. EM6580 operating mode transitions  
POWER-ON  
START-UP  
Power-On-Reset & Power Check Level, ~2.0V  
POR static level  
Power-Check Active  
RC oscilator  
running  
PORwPC  
8 oscillator  
periods  
PORwPC  
RESET  
PORwPC  
resetPortA  
WDreset  
PORwPC  
reset synchronizer  
clocks active  
8 CPU clock  
periods  
Reset-pad  
WDreset  
SleepResCnt  
WakeUp on  
Change  
SLEEP  
Everything stopped  
Registers and  
STAND-BY  
or HALT  
mode  
Clocks active  
ACTIVE  
or running  
mode  
HALT instruction  
interrupt/event  
RAM keep their value  
Sleep bit set  
2.1 ACTIVE Mode  
The active mode is the actual CPU running mode. Instructions are read from the internal ROM and executed by  
the CPU. Leaving the active mode: via the halt instruction to go into standby mode, writing the SLEEP bit to go  
into Sleep mode or detecting the reset to go into reset mode.  
2.2 STANDBY (Halt) Mode  
Executing a HALT instruction puts the EM6580 into standby mode. The voltage regulator, oscillator, watchdog  
timer, interrupts, timers and counters are operating. However, the CPU stops since the clock related to  
instruction execution stops. Registers, RAM and I/O pins retain their states prior to STANDBY mode.  
STANDBY is cancelled by a RESET or an Interrupt request if enabled.  
2.3 SLEEP Mode  
Writing to the Sleep bit in the RegSysCntl1 register puts the EM6580 in sleep mode. The oscillator stops and  
most functions of the EM6580 are inactive. To be able to write to the Sleep bit, the SleepEn bit in  
RegSysCntl2 must first be set to "1". In SLEEP mode only the voltage regulator is active to maintain the RAM  
data integrity, the peripheral functions are stopped and the CPU is reset.all other functions are in reset state.  
SLEEP mode may be cancelled by Wake/Up on change, external reset or by Sleep Reset Counter if any of  
them is enabled.  
Waking up from sleep mode may takes some time to guarantee stable oscillation. Coming back from sleep  
mode puts the EM6681 in reset state and as such reinitializes all registers to their reset value. During sleep  
mode and the following start up the EM6580 is in reset state. Waking up from sleep mode clears the Sleep flag  
but not the SleepEn bit. Inspecting the SleepEn allows to determine if the EM6580 was powered up (SleepEn  
= "0") or woken from sleep mode (SleepEn = "1").  
Copyright © 2007, EM Microelectronic-Marin SA  
03/07, rev. J  
5
www.emmicroelectronic.com  
 

与EM6580SO8A+相关器件

型号 品牌 描述 获取价格 数据表
EM6580SO8B EMMICRO Ultra Low Power 8-pin Flash Microcontroller

获取价格

EM6580SO8B+ EMMICRO Ultra Low Power 8-pin Flash Microcontroller

获取价格

EM6580WP11 EMMICRO Ultra Low Power 8-pin Flash Microcontroller

获取价格

EM6580WP27 EMMICRO Ultra Low Power 8-pin Flash Microcontroller

获取价格

EM6580WS11 EMMICRO Ultra Low Power 8-pin Flash Microcontroller

获取价格

EM6580WS27 EMMICRO Ultra Low Power 8-pin Flash Microcontroller

获取价格