TECHNICAL SPECIFICATIONS
(TA=25°C, airflow rate=300 LFM, Vin=24Vdc, nominal Vout unless otherwise noted.)
PARAMETER
NOTES and CONDITIONS
E24SR05012 (Standard)
Min.
Typ.
Max.
Units
ABSOLUTE MAXIMUM RATINGS
Input Voltage
Continuous
Transient (100ms)
Operating Temperature
Storage Temperature
Input/Output Isolation Voltage
INPUT CHARACTERISTICS
Operating Input Voltage
Input Under-Voltage Lockout
Turn-On Voltage Threshold
Turn-Off Voltage Threshold
Lockout Hysteresis Voltage
Maximum Input Current
No-Load Input Current
36
50
118
125
2250
Vdc
Vdc
°C
°C
Vdc
100ms
Refer to figure 21 for measuring point
-40
-55
18
36
Vdc
16
15
0.7
17
16
1
17.8
17
1.5
3.9
150
10
Vdc
Vdc
Vdc
A
mA
mA
A2s
mA
dB
100% Load, 18Vin
80
3
Off Converter Input Current
Inrush Current (I2t)
0.1
Input Reflected-Ripple Current
Input Voltage Ripple Rejection
OUTPUT CHARACTERISTICS
Output Voltage Set Point
Output Voltage Regulation
Over Load
Over Line
Over Temperature
Total Output Voltage Range
Output Voltage Ripple and Noise
Peak-to-Peak
P-P thru 12µH inductor, 5Hz to 20MHz
120 Hz
15
55
Vin=24V, Io=Io.max, Tc=25°C
4.925
4.875
5.075
Vdc
Io=Io, min to Io, max
Vin=18V to36V
Tc=-40°C to100°C
±3
±3
±50
5
±10
±10
mV
mV
mV
V
Over sample load, line and temperature
5Hz to 20MHz bandwidth
Full Load, 1µF ceramic, 10µF tantalum
Full Load, 1µF ceramic, 10µF tantalum
5.125
50
15
100
30
12
mV
mV
A
RMS
Operating Output Current Range
Output Over Current Protection
DYNAMIC CHARACTERISTICS
Output Voltage Current Transient
Positive Step Change in Output Current
Negative Step Change in Output Current
Settling Time (within 1% Vout nominal)
Turn-On Transient
0
110
Output Voltage 10% Low
140
%
10µF Tan & 1µF Ceramic load cap, 0.1A/µs
50% Io.max to 75% Io.max
150
150
150
250
250
mV
mV
us
75% Io.max to 50% Io.max
Start-Up Time, From On/Off Control
Start-Up Time, From Input
5
5
ms
ms
Back bias start-up
≤ 90% of nominal output voltage
Back drive current limit while pin on-off is enabled
Back drive current limit while pin on-off is disabled
Maximum Output Capacitance
EFFICIENCY
Io=0A
Io=0A
0.1
50
5000
A
mA
µF
Full load; CR mode;5% overshoot of Vout at startup
100% Load
60% Load
90.5
90.5
%
%
ISOLATION CHARACTERISTICS
Input to Output
Isolation Resistance
Isolation Capacitance
FEATURE CHARACTERISTICS
Switching Frequency
2250
Vdc
MΩ
pF
10
1500
350
kHz
ON/OFF Control, Negative Remote On/Off logic
Logic Low (Module On)
-0.7
3
0.5
18
V
V
Logic High (Module Off)
ON/OFF Control, Positive Remote On/Off logic
Logic Low (Module Off)
-0.7
3
0.5
18
V
V
Logic High (Module On)
On/off pin open circuit voltage
On/off pin pull down resistance
Output Voltage Trim Range
Output Voltage Remote Sense Range
Output Over-Voltage Protection
GENERAL SPECIFICATIONS
MTBF
9.6
V
Kohm
%
%
V
12
-10
Pout ≦ max rated power
Pout ≦ max rated power
Over full temp range;
+10
+10
7
5.75
Io=80% of Io, max; Ta=25°C, 300LFM airflow
Refer to figure 21 for measuring point
3.86
22.0
128
M hours
grams
°C
Weight
Over-Temperature Shutdown
DS_E24SR05012_03062007
2