dsPIC33EDV64MC205
16-Bit Digital Signal Controller with High-Speed PWM,
Op Amps, Advanced Analog and MOSFET Driver
Operating Conditions
• Host dsPIC® DSC Core:
Advanced Analog Features
• ADC module:
- 3.0V to 3.6V, -40°C to +85°C, DC to 70 MIPS
- 3.0V to 3.6V, -40°C to +125°C, DC to 60 MIPS
- 3.0V to 3.6V, -40°C to +150°C, DC to 40 MIPS
• MOSFET Gate Driver module:
- 6.5V to 29.0V, -40°C to +150°C
- Fixed output linear regulator, 3.3V @ 70 mA
- Configurable as 10-bit, 1.1 Msps with four S&H
or 12-bit, 500 ksps with one S&H
- Nine ADC inputs
• Flexible and Independent ADC Trigger Sources
• Three Op Amp/Comparators with Direct Connection
to the ADC module:
- Additional dedicated comparator
- Programmable references with 32 voltage
points
Host dsPIC DSC Features
(based on dsPIC33EP64MC206 device):
• Charge Time Measurement Unit (CTMU):
- Supports mTouch® capacitive touch sensing
- Provides high-resolution time measurement (1 ns)
- On-chip temperature measurement
Core: 16-Bit dsPIC33E CPU
• Code Efficient (C and Assembly) Architecture
• Two 40-Bit Wide Accumulators
• Single-Cycle (MAC/MPY) with Dual Data Fetch
• Single-Cycle Mixed-Sign MUL plus Hardware Divide
• 32-Bit Multiply Support
Timers/Output Compare/Input Capture
• 12 General Purpose Timers:
Clock Management
- Five 16-bit and up to two 32-bit timers/counters
- Four Output Compare (OC) modules,
configurable as timers/counters
- PTG module with two configurable timers/
counters
- 32-bit Quadrature Encoder Interface (QEI)
module, configurable as a timer/counter
• Four Input Capture (IC) modules
• Peripheral Pin Select (PPS) to allow Function
Remap
• 1.0% Internal Oscillator
• Programmable PLLs and Oscillator Clock Sources
• Fail-Safe Clock Monitor (FSCM)
• Independent Watchdog Timer (WDT)
• Fast Wake-up and Start-up
Power Management
• Low-Power Management modes (Sleep, Idle, Doze)
• Integrated Power-on Reset and Brown-out Reset
• 0.6 mA/MHz Dynamic Current (typical)
• 30 μA IPD Current (typical)
• Peripheral Trigger Generator (PTG) for Scheduling
Complex Sequences
High-Speed PWM
Communication Interfaces
• Three PWM Pairs with Independent Timing
• Dead Time for Rising and Falling Edges
• 7.14 ns PWM Resolution
• PWM with Support for BLDC and PMSM Control
• Programmable Fault Inputs
• Two UART modules (17.5 Mbps):
- With support for LIN/J2602 protocols and IrDA®
• Two Four-Wire SPI modules (15 Mbps)
• Two I2C modules (up to 1 Mbaud) with SMBus
Support
• Flexible Trigger Configurations for ADC
Conversions
• PPS to allow Function Remap
• Programmable Cyclic Redundancy Check (CRC)
Input/Output
Direct Memory Access (DMA)
• Sink/Source: 12 mA or 6 mA, Pin-Specific for
Standard VOH/VOL, up to 22 or 14 mA, respectively,
for Non-Standard VOH1
• 4-Channel DMA with User-Selectable Priority
Arbitration
• UART, SPI, ADC, IC, OC and Timers
• 5V Tolerant Pins
Debugger Development Support
• Peripheral Pin Select (PPS) to allow Digital Function
Remapping
• Selectable Open-Drain Pull-ups and Pull-Downs
• Up to 5 mA Overvoltage Clamp Current
• Change Notification Interrupts on All I/O Pins
• In-Circuit and In-Application Programming
• Two Program and Two Complex Data Breakpoints
• Trace and Run-Time Watch
2016-2021 Microchip Technology Inc. and its subsidiaries
DS70005292F-page 1