5秒后页面跳转
DS1831 PDF预览

DS1831

更新时间: 2024-01-08 08:46:42
品牌 Logo 应用领域
美信 - MAXIM /
页数 文件大小 规格书
14页 199K
描述
Multisupply Micromonitor

DS1831 技术参数

是否无铅: 不含铅是否Rohs认证: 符合
生命周期:Active零件包装代码:SOIC
包装说明:SOP, SOP16,.25针数:16
Reach Compliance Code:compliantECCN代码:EAR99
HTS代码:8542.39.00.01Factory Lead Time:6 weeks
风险等级:1.33其他特性:POWER-ON-RESET
可调阈值:NO模拟集成电路 - 其他类型:POWER SUPPLY SUPPORT CIRCUIT
JESD-30 代码:R-PDSO-G16JESD-609代码:e3
长度:9.9 mm湿度敏感等级:1
信道数量:4功能数量:1
端子数量:16最高工作温度:85 °C
最低工作温度:-40 °C封装主体材料:PLASTIC/EPOXY
封装代码:SOP封装等效代码:SOP16,.25
封装形状:RECTANGULAR封装形式:SMALL OUTLINE
峰值回流温度(摄氏度):260电源:1/5.5 V
认证状态:Not Qualified座面最大高度:1.75 mm
子类别:Power Management Circuits最大供电电流 (Isup):0.1 mA
最大供电电压 (Vsup):5.5 V最小供电电压 (Vsup):1 V
标称供电电压 (Vsup):3.3 V表面贴装:YES
温度等级:INDUSTRIAL端子面层:Matte Tin (Sn)
端子形式:GULL WING端子节距:1.27 mm
端子位置:DUAL处于峰值回流温度下的最长时间:NOT SPECIFIED
宽度:3.9 mmBase Number Matches:1

DS1831 数据手册

 浏览型号DS1831的Datasheet PDF文件第4页浏览型号DS1831的Datasheet PDF文件第5页浏览型号DS1831的Datasheet PDF文件第6页浏览型号DS1831的Datasheet PDF文件第8页浏览型号DS1831的Datasheet PDF文件第9页浏览型号DS1831的Datasheet PDF文件第10页 
DS1831/A/B  
OUTPUT VALID CONDITIONS  
The DS1831 can maintain valid outputs as long as one input remains above 1.0V. Accurate voltage  
monitoring additionally requires that either the 3.3V IN or 5V IN input be above 1.5V. If this condition is  
not met and at least one of the supply inputs are at or above 1.0V all outputs are maintained in the active  
condition. The DS1831 requires pull-up resistors on the outputs to maintain a valid output. The value of  
the pull up resistor is not critical in most cases but must be set low enough to pull the output to a high  
state. A common pull-up resistor value used is 10k(see Figure 7).  
APPLICATION DIAGRAM—OPEN DRAIN OUTPUTS Figure 7  
3.3V Supply  
5V Supply  
IN5V  
IN3.3v  
1
2
3
16  
10 k  
10 K
ꢀ  
RST3.3V  
RST5V  
15  
14  
DS1831  
TOL5V  
TD5V  
TOL3.3V  
TD3.3V  
4
5
13  
12  
PBRST5V  
PBRST3.3V  
GND  
NOTE: If outputs are at different voltages the outputs can not be connected to form a wired AND.  
OPERATION—NON-MASKABLE INTERRUPT  
The DS1831 has two referenced comparator (DS1831A has only one referenced comparator) that can be  
used to monitor upstream voltages or other system specific voltages. Each comparator is referenced to the  
1.25V internal band gap reference and controls an open-drain output. When a voltage being monitored  
decays to the voltage sense point, the DS1831 pulses the NMI output to the active state for a minimum  
10µs. The comparator detection circuitry also has built-in hysteresis of 100µV. The supply must be below  
the voltage sense point for approximately 2µs before a low NMI will be generated. In this way, power  
supply noise is minimized in the monitoring function, reducing false interrupts. See Figure 8 for the non-  
maskable timing diagram.  
Versatile trip voltages can be configured by the use of an external resistor divider to divide the voltage at  
a sense point to the 1.25V trip levels of the referenced comparators. See Figure 9 for an example circuit  
diagram and sample equations. The equations demonstrate a design process to determine the resistor  
values to use.  
Connecting one or both NMI outputs to one of the reset specific PBRST s allows the non-maskable  
interrupt to generate an automatic reset for the reset time period when an out-of-tolerance condition  
occurs in a monitored supply. An example is shown in Figure 9.  
7 of 14  

与DS1831相关器件

型号 品牌 描述 获取价格 数据表
DS1831/A/B ETC Multisupply Micromonitor

获取价格

DS1831/T&R DALLAS Power Supply Support Circuit, Fixed, 4 Channel, PDIP16, 0.300 INCH, DIP-16

获取价格

DS1831+ MAXIM Power Supply Support Circuit, Fixed, 4 Channel, PDIP16, 0.300 INCH, DIP-16

获取价格

DS1831A MAXIM Multisupply Micromonitor

获取价格

DS1831A ROCHESTER 4-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP16, 0.300 INCH, PLASTIC, DIP-16

获取价格

DS1831A ADI 多电源MicroMonitor?

获取价格