5秒后页面跳转
DS1090U-2/T PDF预览

DS1090U-2/T

更新时间: 2024-02-08 10:10:02
品牌 Logo 应用领域
美信 - MAXIM /
页数 文件大小 规格书
8页 999K
描述
Clock Generator, 4MHz, CMOS, PDSO8, MICRO, SOP-8

DS1090U-2/T 技术参数

是否无铅: 不含铅是否Rohs认证: 符合
生命周期:Active零件包装代码:SOIC
包装说明:TSSOP,针数:8
Reach Compliance Code:compliantECCN代码:EAR99
HTS代码:8542.39.00.01风险等级:5.43
JESD-30 代码:S-PDSO-G8JESD-609代码:e3
长度:3 mm端子数量:8
最高工作温度:85 °C最低工作温度:-40 °C
封装主体材料:PLASTIC/EPOXY封装代码:TSSOP
封装形状:SQUARE封装形式:SMALL OUTLINE, THIN PROFILE, SHRINK PITCH
峰值回流温度(摄氏度):NOT SPECIFIED认证状态:Not Qualified
座面最大高度:1.1 mm最大供电电压:5.5 V
最小供电电压:3 V表面贴装:YES
技术:CMOS温度等级:INDUSTRIAL
端子面层:MATTE TIN端子形式:GULL WING
端子节距:0.65 mm端子位置:DUAL
处于峰值回流温度下的最长时间:NOT SPECIFIED宽度:3 mm
uPs/uCs/外围集成电路类型:CLOCK GENERATOR, OTHERBase Number Matches:1

DS1090U-2/T 数据手册

 浏览型号DS1090U-2/T的Datasheet PDF文件第2页浏览型号DS1090U-2/T的Datasheet PDF文件第3页浏览型号DS1090U-2/T的Datasheet PDF文件第4页浏览型号DS1090U-2/T的Datasheet PDF文件第5页浏览型号DS1090U-2/T的Datasheet PDF文件第6页浏览型号DS1090U-2/T的Datasheet PDF文件第7页 
Low-Frequency, Spread-Spectrum  
EconOscillator  
R
Resistor Selection  
SET  
Table 2. Dither Percentage Setting  
The value of the resistor used to select the desired fre-  
quency is calculated using the formula in the Master  
Oscillator section (see also Figure 1). It is recommended  
to use, at minimum, a 1%-tolerance, 1/16th-watt compo-  
nent with a temperature coefficient that satisfies the over-  
all stability requirements desired of the end-equipment.  
J1  
0
J0  
0
DITHER PERCENT (%)  
0
2
4
8
0
1
1
0
Place the external R  
resistor as close as possible to  
minimize lead inductance.  
SET  
1
1
Dither Percentage Settings  
Power-Supply Decoupling  
To achieve best results, it is highly recommended that a  
decoupling capacitor is used on the IC power-supply  
pins. Typical values of decoupling capacitors are 0.01µF  
and 0.1µF. Use a high-quality, ceramic, surface-mount  
Dither amplitude (measured in percent from the mas-  
ter oscillator center frequency) is set using input pins  
J0 and J1. This circuit uses a sense current from the  
master oscillator bias circuit to adjust the amplitude of  
the triangle-wave signal to a voltage level that modu-  
lates the master oscillator to a percentage of its resis-  
tor-set center frequency. This percentage is set in the  
end application to be 0%, 2%, 4%, or 8% (see Table 2).  
capacitor, and mount it as close as possible to the V  
and GND pins of the IC to minimize lead inductance.  
CC  
Application Information  
Chip Information  
TRANSISTOR COUNT: 1883  
Pin Connection  
The DS1090 is intended to provide a fixed-frequency,  
dithered clock to be used as a clock driver for DC-DC  
converters and other applications requiring a low-  
frequency EMI-reduced clock oscillator. All control pins  
must be biased per Tables 1 and 2 for proper operation  
SUBSTRATE CONNECTED TO GROUND  
Package Information  
For the latest package outline information, go to  
for the individual application’s requirements. R  
must  
SET  
www.maxim-ic.com/DallasPackInfo.  
be tied to ground (GND) by a customer-supplied resistor.  
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are  
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.  
8 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600  
© 2004 Maxim Integrated Products  
Printed USA  
is a registered trademark of Maxim Integrated Products.  
is a registered trademark of Dallas Semiconductor Corporation.  

与DS1090U-2/T相关器件

型号 品牌 描述 获取价格 数据表
DS1090U-2/V+T MAXIM Analog Circuit, PDSO8,

获取价格

DS1090U-2+ MAXIM Clock Generator, CMOS, PDSO8, LEAD FREE, USOP-8

获取价格

DS1090U-2+T MAXIM Clock Generator, 4MHz, CMOS, PDSO8, USOP-8

获取价格

DS1090U-2+W MAXIM Analog Circuit, PDSO8

获取价格

DS1090U-32 MAXIM Low-Frequency, Spread-Spectrum EconOscillator

获取价格

DS1090U-32/T MAXIM Clock Generator, 0.25MHz, CMOS, PDSO8, MICRO, SOP-8

获取价格