Datasheet > DPA426

DPA426

更新时间： 2024-02-10 13:51:29

品牌	Logo	应用领域
帕沃英蒂格盛 - POWERINT		转换器
页数	文件大小	规格书
36页	289K
描述
Highly Integrated DC-DC Converter ICs for Distributed Power Architectures

阅读下载

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

DPA426 技术参数

是否无铅：	含铅	是否Rohs认证：	不符合
生命周期：	Active	零件包装代码：	SFM
包装说明：	,	针数：	6
Reach Compliance Code：	compliant	风险等级：	5.32
模拟集成电路 - 其他类型：	SWITCHING REGULATOR	控制模式：	VOLTAGE-MODE
控制技术：	PULSE WIDTH MODULATION	最大输入电压：	75 V
最小输入电压：	16 V	标称输入电压：	40 V
JESD-30 代码：	R-PSSO-G6	JESD-609代码：	e0
长度：	9.4 mm	功能数量：	1
端子数量：	6	最高工作温度：	125 °C
最低工作温度：	-40 °C	最大输出电流：	1.75 A
封装主体材料：	PLASTIC/EPOXY	封装形状：	RECTANGULAR
封装形式：	SMALL OUTLINE	峰值回流温度（摄氏度）：	NOT SPECIFIED
认证状态：	Not Qualified	座面最大高度：	2.054 mm
表面贴装：	YES	切换器配置：	SINGLE
最大切换频率：	425 kHz	技术：	CMOS
温度等级：	AUTOMOTIVE	端子面层：	Tin/Lead (Sn/Pb)
端子形式：	GULL WING	端子节距：	1.27 mm
端子位置：	SINGLE	处于峰值回流温度下的最长时间：	NOT SPECIFIED
宽度：	8 mm

DPA426 数据手册

DPA423-426

approximately 5.8 V, the control circuitry is activated and the

soft-start begins. The soft-start circuit gradually increases the

duty cycle of the MOSFET from zero to the maximum value

over approximately 5 ms. The high voltage current source is

turned off at the end of the soft-start. If no external feedback/

supply current is fed into the CONTROL pin by the end of the

soft-start, the CONTROL pin will start discharging in response

to the supply current drawn by the control circuitry and the gate

current of the switching MOSFET driver. If the power supply

is designed properly, and no fault condition such as open loop

or overloaded output exists, the feedback loop will close,

providing external CONTROL pin current, before the

CONTROL pin voltage has had a chance to discharge to the

lowerthresholdvoltageofapproximately4.8V(internalsupply

under-voltage lockout threshold). When the externally fed

current charges the CONTROL pin to the shunt regulator

voltage of 5.8 V, current in excess of the consumption of the

chip is shunted to SOURCE through resistor R_Eas shown in

Figure 2. This current flowing through R_Econtrols the duty

cycle of the power MOSFET to provide closed loop regulation.

The shunt regulator has a finite low output impedance Z_Cthat

sets the gain of the error amplifier when used in a primary

feedback configuration. The dynamic impedance Z_Cof the

CONTROL pin together with the external CONTROL pin

capacitance sets the dominant pole for the control loop.

currentstandbymode. Thehigh-voltagecurrentsourceturnson

and charges the external capacitance again. A hysteretic

internal supply under-voltage comparator keeps V_Cwithin a

window of typically 4.8 to 5.8 V by turning the high-voltage

current source on and off as shown in Figure 5. The auto-restart

circuit has a divide-by-8 counter that prevents the output

MOSFET from turning on again until eight discharge/charge

cycles have elapsed. This is accomplished by enabling the

output MOSFET only when the divide-by-8 counter reaches

full count (S7). The counter effectively limits DPA-Switch

power dissipation as well as the maximum power delivered to

the power supply output by reducing the auto-restart duty cycle

to typically 4%. Auto-restart mode continues until output

voltage regulation is again achieved through closure of the

feedback loop.

Oscillator and Switching Frequency

Theinternaloscillatorlinearlychargesanddischargesaninternal

capacitance between two voltage levels to create a sawtooth

waveform for the pulse width modulator. The oscillator sets

both the pulse width modulator latch and the current limit latch

at the beginning of each cycle.

The nominal switching frequency of 400 kHz was chosen to

minimize the transformer size and to allow faster power supply

loop response. The FREQUENCY pin, when shorted to the

CONTROL pin, lowers the switching frequency to 300 kHz,

which may be preferable in some applications such as those

employing secondary synchronous rectification. Otherwise,

theFREQUENCYpinshouldbeconnectedtotheSOURCEpin

for the default 400 kHz.

When a fault condition such as an open loop or overloaded

output prevents the flow of an external current into the

CONTROLpin,thecapacitorontheCONTROLpindischarges

towards4.8V. At4.8Vauto-restartisactivatedwhichturnsthe

output MOSFET off and puts the control circuitry in a low

V_UV

V_LINE

0 V

S7 S0

S1 S2

5.8 V

4.8 V

V_C

0 V

V_DRAIN

0 V

V_OUT

0 V

Note: S0 through S7 are the output states of the auto-restart counter

PI-2545-050602

Figure 5. Typical Waveforms for (1) Power Up (2) Normal Operation (3) Auto-restart (4) Power Down.

1/04

1 2 3 456 7 8...36

下载PDF

与DPA426相关器件

型号	品牌	描述	获取价格	数据表
DPA426G	POWERINT	Highly Integrated DC-DC Converter ICs for Power over Ethernet & Telecom Applications	获取价格
DPA426GN	POWERINT	Highly Integrated DC-DC Converter ICs for Power over Ethernet & Telecom Applications	获取价格
DPA426GN-TL	POWERINT	Highly Integrated DC-DC Converter ICs for Power over Ethernet & Telecom Applications	获取价格
DPA426G-TL	POWERINT	Highly Integrated DC-DC Converter ICs for Power over Ethernet & Telecom Applications	获取价格
DPA426P	POWERINT	Highly Integrated DC-DC Converter ICs for Power over Ethernet & Telecom Applications	获取价格
DPA426PN	POWERINT	Highly Integrated DC-DC Converter ICs for Power over Ethernet & Telecom Applications	获取价格

与DPA426相关文章

PCF8574资料解读：主要参数分析、引脚说明
2024-05-21

7
AD637数据手册解读：主要特性、引脚及其功能解读、电气参数
2024-05-21

6
ADUM1201资料手册解读：参数分析、引脚说明、应用分析
2024-05-21

9
一文带你了解压敏电阻器在直流电路中的过压保护作用
2024-05-21

5

产品中心

服务支持

精选活动

关于我们

帮助中心

DPA426

DPA426 技术参数

DPA426 数据手册

与DPA426相关器件

与DPA426相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

DPA426

DPA426 技术参数

DPA426 数据手册

与DPA426相关器件

与DPA426相关文章

您还可以找

您在本页遇到什么问题？