5/14
Reference Only
Spec No.J(E)TE243C-9110F
DFEG7030D Type 信頼性試験項目一覧 Reliability Test Item List [1/2]
項 目 Item
規 格 Specification
条 件 Condition
1 耐熱性
初期値に対する
温度+125℃中に 1000時間放置後、常温常湿中に
放置し、24±2時間以内に測定。
High Temperature Exposure
Lの変化率 ± 10%以内
AEC-Q200 Test No.3 Change from an initial value
within ± 10%
The specimen shall be stored at a temperature of +125℃
for 1000 h. Then it shall be stabilized under standard
atmospheric conditions.
L
:
Measurement at 24±2 hours after test conclusion.
2 温度サイクル
初期値に対する
Lの変化率 ± 10%以内
-40℃(30分)→常温(2分以内)→+125℃(30分)→常温
(2分以内)を1サイクルとし、これを 1000サイクル行い、
常温常湿中に放置し、24±2時間以内に測定。
Temperature Cycling
AEC-Q200 Test No.4 Change from an initial value
within ± 10%
The specimen shall be subjected to 1000 continuous cycles
of temperature change of -40℃ for 30 min and +125℃ for
30 min with the transit period of 2min or less. Then it shall be
stabilized under standard atmospheric conditions.
L
:
Measurement at 24±2 hours after test conclusion.
3 耐湿性
Biased Humidity
初期値に対する
Lの変化率 ± 10%以内
温度+85℃、湿度85%中に 1000時間放置後、
常温常湿中に放置し、24±2時間以内に測定。
AEC-Q200 Test No.7 Change from an initial value
within ± 10%
The specimen shall be stored at a temperature of +85℃
with relative humidity of 85% for 1000 h. Then it shall be
stabilized under standard atmospheric conditions.
Measurement at 24±2 hours after test conclusion.
L
:
4 高温負荷
Operational Life
初期値に対する
Lの変化率 ± 10%以内
温度+85℃中に 1000時間定格電流印加後、
常温常湿中に放置し、24±2時間以内に測定。
Change from an initial value
The specimen shall be stored attime-rating current
in temperature +85℃ after 1000 h. Then it shall be
stabilized under standard atmospheric conditions.
Measurement at 24±2 hours after test conclusion.
AEC-Q200 Test No.8
L
:
within ± 10%
5 外形寸法
Physical Dimension
外形寸法仕様による
デジタルノギスおよび光学顕微鏡を用いて測定
AEC-Q200 Test No.10 According to specification
Measures using digital slide calipers and an optical microscope.
6 耐薬品性試験
初期値に対する
イソプロピルアルコール(+25±5℃)中に5分間浸し
1時間放置後、測定。
Resistance to Solvent Lの変化率 ± 10%以内
AEC-Q200 Test No.12 Change from an initial value
Immerse in Isopropyl-Alcohol for 5 minutes at +25±5°C.
Measurement at 1 hour after test conclusion.
L
:
within ±10%
: 981 m/s2 (≒100G)
7 耐衝撃性
初期値に対する
加速度 Peak acceleration
Mechanical shock
Lの変化率 ± 10%以内
作用時間 Duration of pulse : 6 ms
6方向に各 3回(計 18回) : 3 times in each of 6(±X, ±Y, ±Z) axes.
AEC-Q200 Test No.13 Change from an initial value
within ± 10%
Three successive shock shall be applied in the perpendicular
direction of each surface of the specimen.
L
:
8 耐振性
初期値に対する
Lの変化率 ± 10%以内
掃引割合10~2000~10Hz、掃引時間20分、全振幅1.5mm、
5G X・Y・Z 方向に各 4時間(計 12時間)加える。
Vibration
AEC-Q200 Test No.14 Change from an initial value
within ± 10%
The specimen shall be subjected to a vibration of 1.5mm
amplitude , sweep time 20min , 5G , sweep frequency 10~2000Hz
(10Hz to 2000Hz to 10Hz) for 4 h in each of 3(X, Y, Z) axes.
L
: