Document 550
For Analog Devices ADM2485
Isolated RS-485 Transceiver
SMT Power Transformers
• Developed specifically for Analog Devices ADM2485
Isolated RS-485 Transceiver for stepping up 5 V or 3.3 V to 6 V.
• Center tapped primary and secondary windings
• 2500 Vrms interwinding isolation.
Core material Ferrite
Terminations RoHS tin-silver over tin over nickel over phos
bronze. Other terminations available at additional cost.
Weight 0.94 – 1.0 g
Ambient temperature –40°C to +125°C
Storage temperature Component: –40°C to +125°C.
Packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 600/13″ reel Plastic tape: 24 mm wide, 0.37 mm thick,
16 mm pocket spacing, 6.1 mm pocket depth
PCB washing Only pure water or alcohol recommended
Leakage
inductance4
max (µH)
Volt-time
product5
(V-µsec)
DCR max (Ohms)3
Pri /sec
voltage
Inductance2
min (µH)
Power6 Turns ratio
Part number1
pri
sec
(W)
pri : sec
DA2303-AL_
DA2304-AL_
5 V to 6 V
3.3 V to 6 V
45.6
17.8
0.130
0.086
0.260
0.232
1.0
0.43
34.4
21.5
7.2
7.2
1 : 1.5
1 : 2.2
1. When ordering, please specify termination and packaging codes:
4
8
Dot indicates pin 1
8
DA2303-ALD
1
Termination: L = RoHS compliant tin-silver over tin over nickel over
phos bronze.
Special order: T = RoHS tin-silver-copper (95.5/4/0.5)
or S = non-RoHS tin-lead (63/37).
Packaging: D =13″ machine ready reel. EIA-481 embossed plastic
tape (600 per full reel).
3
2
7
Pri
Sec
0.394
10,00
max
6
4
5
1
5
0.475
max
B= Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter D instead.
Primary windings and secondary
windings to be connected
12,07
in series on the PC board.
2. Inductance is tested between pins 4 and 3 at 500 kHz, 0.5 Vrms, 0 Adc.
3. DCR is per winding.
4. Leakage inductance is for the primary with both windings connected in
series and with the secondary windings shorted.
5. Based on Bsat of the core at 25°C and number of turns on winding 4-3.
6. Calculated output power based on 150 kHz operating frequency. Power
varies depending on application.
0.235
5,97
max
0.004/0,10
0.319 ±0.004
8,1 ±0,1
0.028
0,70
0.358
9,10
0.067
1,70
7. Operating temperature range -40°C to +85°C.
8. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
4
1
0.079
2,00
5
8
1
Recommended
Land Pattern
0.079
2,00
0.063
1,60
inches
mm
Dimensions are in
Specifications subject to change without notice.
Please check our website for latest information.
Document550 Revised01/05/09
© Coilcraft, Inc. 2010