CWR06
Vishay Sprague
www.vishay.com
TAPE AND REEL PACKAGING in inches [millimeters]
Note
• Metric dimensions will govern. Dimensions in inches are rounded and for reference only.
0.157 0.004
[4.0 0.10]
10 pitches cumulative
tolerance on tape
0.008 [0.200]
T2
(max.)
Deformation
between
embossments
0.059 + 0.004 - 0.0
[1.5 + 0.10 - 0.0]
Embossment
0.024
[0.600]
max.
0.079 0.002
[2.0 0.05]
0.069 0.004
[1.75 0.10]
Top
cover
tape
A0
0.030 [0.75]
min. (3)
20°
F
W
B1 (max.) (6)
K0
Top
cover
tape
Maximum
component
rotation
B0
P1
0.030 [0.75]
min. (4)
(Side or front sectional view)
Center lines
of cavity
For tape feeder
reference only
including draft.
D1 (min.) for components
0.004 [0.10]
max.
(5)
.
0.079 x 0.047 [2.0 x 1.2] and larger
USER DIRECTION
OF FEED
Maximum
cavity size (1)
Concentric around B0
Cathode (-)
R minimum:
8 mm = 0.984" (25 mm)
12 mm and 16 mm = 1.181" (30 mm)
R
Anode (+)
min.
DIRECTION OF FEED
3.937 [100.0]
Bending radius (2)
20° maximum
component rotation
0.039 [1.0]
max.
Typical
component
cavity
center line
Tape
0.039 [1.0]
max.
Tape and reel specifications: All case sizes are
available on plastic embossed tape per EIA-481.
Standard reel diameter is 7" (178 mm).
B0
0.9843 [250.0]
Typical
Camber
component
center line
(Top view)
A0
Allowable camber to be 0.039/3.937 [1/100]
Non-cumulative over 9.843 [250.0]
(Top view)
Notes
(1)
A0, B0, K0, are determined by the maximum dimensions to the ends of the terminals extending from the component body and/or the body
dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of the
cavity (A0, B0, K0) must be within 0.002" (0.05 mm) minimum and 0.020" (0.50 mm) maximum. The clearance allowed must also prevent
rotation of the component within the cavity of not more than 20°.
(2)
(3)
(4)
(5)
(6)
Tape with components shall pass around radius “R” without damage. The minimum trailer length may require additional length to provide
“R” minimum for 12 mm embossed tape for reels with hub diameters approaching N minimum.
This dimension is the flat area from the edge of the sprocket hole to either outward deformation of the carrier tape between the embossed
cavities or to the edge of the cavity whichever is less.
This dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier
tape between the embossed cavity or to the edge of the cavity whichever is less.
The embossed hole location shall be measured from the sprocket hole controlling the location of the embossement. Dimensions of
embossement location shall be applied independent of each other.
B1 dimension is a reference dimension tape feeder clearance only.
CARRIER TAPE DIMENSIONS in inches [millimeters]
CASE CODE
TAPE SIZE
B1 (max.)
D1 (min.)
F
P1
T2 (max.)
W
0.039
[1.0]
0.138 0.002
[3.5 0.05]
0.157 0.004
[4.0 0.1]
0.098
[2.5]
0.315 0.004
[8.0 0.10]
A
8 mm
0.179 [4.55]
0.059
[1.5]
0.059
[1.5]
0.059
[1.5]
0.217 0.002
[5.5 0.05]
0.217 0.002
[5.5 0.05]
0.295 0.004
[7.5 0.1]
0.157 0.004
[4.0 0.1]
0.315 0.004
[8.0 0.10]
0.315 0.004
[8.0 0.10]
0.256
[6.5]
0.256
[6.5]
0.315
[8.0]
0.472 0.012
[12.0 0.30]
0.472 0.012
[12.0 0.30]
0.642 max.
[16.3] max.
B, C, D, E
12 mm
0.323 [8.2]
0.323 [8.2]
0.476 [12.1]
12 mm
double pitch
F
G, H
16 mm
Revision: 27-Feb-13
Document Number: 40009
5
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
5秒后页面跳转
STM32H743技术深度剖析与应用案例探索
LM321中文资料解析：引脚功能介绍、技术特点、技术特性分析
74HC14芯片资料介绍：性能特性分析、引脚介绍
LM1875芯片手册：功放参数分析、引脚说明、电路设计要点
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
