Datasheet > BZX85C8V2TA

BZX85C8V2TA

更新时间： 2022-12-01 21:05:34

品牌	Logo	应用领域
TAK_CHEONG		/
页数	文件大小	规格书
7页	846K
描述
Zener Diode, 8.2V V(Z), 6.1%, 1.3W, Silicon, Unidirectional, DO-41, HERMETIC SEALED, GLASS, DO-204AL, 2 PIN

阅读下载

中文翻译

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

BZX85C8V2TA 数据手册

BZX85C3V3 through BZX85C100 Series

APPLICATION NOTE

Since the actual voltage available from a given zener

∆T is the increase in junction temperature above the lead

diode is temperature dependent, it is necessary to determine

junction temperature under any set of operating conditions

in order to calculate its value. The following procedure is

recommended:

temperature and may be found as follows:

∆T_JL= θ_JLP_D.

may be determined from Figure 3 for dc power

conditions. For worst-case design, using expected limits of

I , limits of P and the extremes of T (∆T ) may be

Lead Temperature, T , should be determined from:

T_L= θ_LAP_D+ T_A.

estimated. Changes in voltage, V , can then be found from:

is the lead-to-ambient thermal resistance (°C/W) and P

∆V = θ_VZ∆T_J.

is the power dissipation. The value for θ will vary and

, the zener voltage temperature coefficient, is found

depends on the device mounting method. θ is generally 30

from Figure 2.

to 40°C/W for the various clips and tie points in common use

and for printed circuit board wiring.

Under high power-pulse operation, the zener voltage will

vary with time and may also be affected significantly by the

zener resistance. For best regulation, keep current

excursions as low as possible.

Surge limitations are given in Figure 5. They are lower

than would be expected by considering only junction

temperature, as current crowding effects cause temperatures

to be extremely high in small spots, resulting in device

degradation should the limits of Figure 5 be exceeded.

The temperature of the lead can also be measured using a

thermocouple placed on the lead as close as possible to the

tie point. The thermal mass connected to the tie point is

normally large enough so that it will not significantly

respond to heat surges generated in the diode as a result of

pulsed operation once steady-state conditions are achieved.

Using the measured value of T , the junction temperature

may be determined by:

T_J= T_L+ ∆T_JL

http://www.takcheong.com

1...4 5 67

中文翻译

下载PDF

与BZX85C8V2TA相关器件

型号	品牌	描述	获取价格	数据表
BZX85C8V2TA2	TAK_CHEONG	Zener Diode, 8.2V V(Z), 6.1%, 1.3W, Silicon, Unidirectional, DO-41, HERMETIC SEALED, GLASS	获取价格
BZX85C8V2-TAP	VISHAY	DIODE ZENER 8.2V 1.3W DO41	获取价格
BZX85C8V2-TR/5	VISHAY	DIODE ZENER DIODE,SINGLE, TWO TERMINAL,8.2V V(Z),5%,DO-41, Voltage Regulator Diode	获取价格
BZX85C91	GOOD-ARK	SILICON PLANAR POWER ZENER DIODES	获取价格
BZX85C91	TSC	Voltage Range 2.4 to 212 Volts 1.3Watts Power Dissipation	获取价格
BZX85C91	VISHAY	Zener Diodes	获取价格