BWR Models
7-10W, Dual Output DC/DC converters
Performance/Functional Specifications
Typical @ TA = +2±°C under nominal line voltage and full-load conditions, unless noted0 ➀
Input
Absolute Maximum Ratings
Input Voltage Range:
Input Voltage:
D± Models
D±A Models
Dꢁ2A Models
D48A Models
40ꢀ-ꢀ02± Volts (±V nominal)
9-ꢁ8 Volts (ꢁ2V nominal)
ꢁ8-ꢀ± Volts (48V nominal)
ꢁ7 Volts
27 Volts
87Volts
Dꢁ2 Models
D48 Models
Input Current
See Ordering Guide
Input Reverse-Polarity Protection
Current must be <6A0 Brief
duration only0 Fusing recommended0
Input Filter Type ➁
Reverse-Polarity Protection
Pi
Output Overvoltage Protection
±±V Outputs
±ꢁ2V Outputs
Yes (Instantaneous, 6A maximum)
ꢁ. Volts, limited duration
28 Volts, limited duration
.6 Volts, limited duration
Output
±ꢁ±V Outputs
VOUT Accuracy (±73 load):
±±V Outputs
Output Current
Current limited0 Max0 current and
short-circuit duration are model
dependent0
±ꢁ0±3, maximum
±ꢁ3, maximum
±ꢁ2/ꢁ±V Outputs
Temperature Coefficient
Ripple/Noise (27MHz BW) ➁
Line/Load Regulation
Efficiency
±70723 per °C
Storage Temperature
–47 to +ꢁ7±°C
+.77°C
See Ordering Guide
See Ordering Guide
See Ordering Guide
ꢁ±77Vdc, minimum (functional)
277pF
Lead Temperature (soldering, ꢁ7 sec0)
These are stress ratings0 Exposure of devices to any of these conditions may adversely
affect long-term reliability0 Proper operation under conditions other than those listed in the
Performance/Functional Specifications Table is not implied0
Isolation Voltage ➂
Isolation Capacitance
Current Limiting
Auto-recovery
Overvoltage Protection ➃
Zener/transorb clamps, magnetic feedback
T E C H N I C A L N O T E S
Dynamic Characteristics
Transient Response (±73 load step)
277µsec max0 to ±ꢁ0±3 of final value
ꢁ6±kHz (±ꢁ±kHz)
Floating Outputs
Switching Frequency
Since these are isolated DC/DC converters, their outputs are "floating." Any
BWR model may be configured to produce an output of 10V, 24V or 30V (for
5V, 12V or 15V models, respectively) by applying the load across the
+Output and –Output pins (pins 3 and 5), with either output grounded. The
Common pin (pin 4) should be left open. Minimum 20ꢀ loading is recom-
mended under these conditions.
Environmental
Operating Temperature (ambient):
Without Derating
–47 to +6±/ꢀ7°C (Model dependent)
to +ꢁ77°C (See Derating Curves)
With Derating
Storage Temperature
–47 to +ꢁ7±°C
Physical
Filtering and Noise Reduction
Dimensions
Shielding
2" x ꢁ" x 70.ꢀ±" (±ꢁ x 2± x 90±mm)
±-sided
All A-Series BWR 7-10 Watt DC/DC Converters achieve their rated ripple
and noise specifications without the use of external input/output capaci-
tors. In critical applications, input/output ripple and noise may be further
reduced by installing electrolytic capacitors across the input terminals and/
or low-ESR tantalum or electrolytic capacitors across the output terminals.
Output capacitors should be connected between their respective output pin
(pin 3 or 5) and Common (pin 4) as shown in Figure 2. The caps should be
located as close to the power converters as possible. Typical values are
listed in the tables below. In many applications, using values greater than
those listed will yield better results.
Case Connection:
D±A and Dꢁ2A Models
D48A Models
Pin 2 (–VIN)
Pin ꢁ (+VIN)
Case Material
Corrosion resistant steel with
non-conductive, epoxy-based black
enamel finish and palstic baseplate
Pin Material
RoHS: Gold-plated copper alloy with nickel
underplate
Non-RoHS: Solder-coated brass
Weight
ꢁ0. ounces (.ꢀ grams)
UL 94V-7
Flammability
To Reduce Input Ripple
"D±A" Models
"Dꢁ2A" Models
"D48A" Models
4ꢀµF, ꢁ7V
27µF, .±V
ꢁ7µF, ꢁ77V
➀ These power converters require a minimum 273 loading on each output to maintain
specified regulation0 Operation under no-load conditions will not damage these devices;
however they may not meet all listed specifications0
➁ Application-specific internal input/output filtering can be recommended or perhaps added
internally upon request0 Contact MPS Applications Engineering for details0
➂ Devices can be screened or modified for higher guaranteed isolation voltages0
Contact MPS Applications Engineering for details0
To Reduce Output Ripple
±±V Output
4ꢀµF, ꢁ7V, Low ESR
22µF, 27V, Low ESR
➃ D±A Models: Zener/transorb only
±ꢁ2/ꢁ±V Outputs
In critical, space-sensitive applications, MPS may be able to tailor the internal
input/output filtering of these units to meet your specific requirements0 Con-
tact our Applications Engineering Group for additional details0
www.murata-ps.com/support
MDC_BWR-7-10_C03 Page 3 of 5