®
®
Environmental performance
Characteristics
Value
IEC international
MIL-spec tests
-55°C/+200°C 1) (HEl model: -20°C/+80°C)
-20°C/+200°C 2) (HEl model: -20°C/+80°C)
IP 68 (at 2 m, 15Hr)
Operating temperature (mated)
Ingress protection index
Fungus
IEC 60529
Satisfied - by material analysis
60 sec. front and back face
MIL-STD 810F-508.5
EIA-364-104A
Flammability
Fluid contamination 3)
Sand and dust 4)
Lightning strike
Altitude-low temp 5)
Salt fog 6)
Fuels, gasoline, hydraulic oils, solvents, de-icing
6 hr, 55°C, blowing < 150 µm dust
10 K amps - 6 times
MIL-STD-810F method 504
MIL-STD 810F-510.4
EIA-364-75
-65°C; 40’000 feet and 400 VAC
Alum. shell (up to 500Hr), Brass shell (1000Hr)
5 cycles: -65°C to +150°C
EIA-364-105A
IEC 60512-6 test 11f
IEC 60512-11-4
EIA-364-26
Thermal shock
Altitude immersion
Humidity
EIA-364-32 test condition IV
EIA-364-03
No moisture on contacts
21 days at 95%
IEC 60068-2
EIA-364-31 method IV
Note:
1) Shell material code C + Silicone O-ring (see page 1).
2) Shell material code I/X + FPM O-ring (see page 1).
3) Connectors immersed at both 70°C and 25°C according to specification. Connectors are then inspected, no visual signs of damage seen.
Fuels: Kerosene, JP4, (Nato F40) at 70°C +/- 2°C. Gasoline: ASTM 4814. Hydraulic oils: Mineral oil based MIL-H-5606.
Solvents: Isopropanol. De-icing fluids: 25% ethylene glycol.
4) No signs of damage, connectors opened and closed without difficulty. Dust or sand was not inside connector.
5) Wired mated connectors = no voltage breakdown, shell to all contacts (connected together) w/400 VAC after 1 hour at -65° C at 40’000 feet altitude.
6) Corrosion resistance. Inspection: salt deposits shall be removed by gentle wash in running water with light brushing using soft brush.
Aluminium Shell (material code: X) max: 48 hours, (material code: I) max: 500 hours. Brass shell (material code: C) over 1000 hours.
Electrical performance
Characteristics
Value
IEC international
MIL-spec tests
EIA-364-21
Insulation resist. (at ambient temp.) 6)
Dielectric withstanding volt. (sea level)
Contact resistance
> 1012 Ω, > 1010 Ω (after humidity)
See table page 25, 26, 27
IEC 60512-2 test 3a
IEC 60512-2 test 4a
IEC 60512-2 test 2a
IEC 60512-3 test 5a
IEC 60512-2-6
EIA-364-20
EIA-364-06
See table below 7)
Current rating
See insulator configuration page 25, 26, 27
< 1.5m Ω
Shell to shell conductivity
EIA-364-83
EIA-364-66
EIA-364-66
Shielding effectiveness, low frequency
Shielding effectiveness, high frequency
≥ 80 dB up to 1GHz
≥ 70 dB (3GHz), ≥ 58 dB (6GHz), ≥ 40 dB (10GHz)
Note: 6) After humidity test: 21 days at 95% RH according to IEC 60068-2. Insulation resistance measured between the contacts and contact/shell.
Contact resistance 7)
Value
IEC 60512-2 test 2a
ø A
(mm)
0.5
0.7
0.9
1.3
mΩ
≤ 8.7 ≤ 6.1 ≤ 4.8 ≤ 3.6
Notes: 7) after 5000 mating cycles and the salt spray test according to IEC 60512-6 test 11 f.
2
www.lemo.com
5秒后页面跳转
PCF8574资料解读：主要参数分析、引脚说明
AD637数据手册解读：主要特性、引脚及其功能解读、电气参数
ADUM1201资料手册解读：参数分析、引脚说明、应用分析
一文带你了解压敏电阻器在直流电路中的过压保护作用
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
