BCM4330 Preliminary Data Sheet
Revision History
FEATURES
FEATURES
IEEE 802.11x Key Features
Bluetooth and FM Key Features
• Single-band 2.4 GHz 802.11 b/g/n or dual-
band 2.4 GHz and 5 GHz 802.11 a/b/g/n (non-
simultaneous)
• Single stream 802.11n support for 20 MHz
channels provides PHY layer rates up to MCS7
(72 Mbps) for typical upper-layer throughput
in excess of 45 Mbps.
• Integrated CMOS power amplifiers with
internal power-detectors and closed-loop
power control can deliver greater than
18 dBm of linear output power (in 2.4 GHz
band).
• Bluetooth Core Specification Version 4.0 + HS compliant
with provisions for supporting future specifications
• Bluetooth Class 1 or Class 2 transmitter operation
• Supports extended Synchronous Connections (eSCO), for
enhanced voice quality by allowing for retransmission of
dropped packets
• Adaptive Frequency Hopping (AFH) for reducing radio
frequency interference
• Interface support—Host Controller Interface (HCI) using
a high-speed UART interface and PCM for audio data
• The FM unit supports HCI for communication, stereo
analog input and output
• PAs can be powered directly from VBAT,
• Low-power consumption improves battery life of
handheld devices
• FM receiver: 65 MHz to 108 MHz FM bands; supports the
European Radio Data Systems (RDS) and the North
American Radio Broadcast Data System (RBDS) standards
eliminating the need for a PALDO.
• Up to 8 RF control signals are available to
support optional external PAs for higher
output power and LNAs for enhanced
sensitivity.
• Supports multiple simultaneous Advanced Audio
• Supports a single 2.4 GHz antenna shared
Distribution Profiles (A2DP) for stereo sound
between WLAN and Bluetooth.
• Automatic frequency detection for standard crystal and
TCXO values
• FM transmitter: 65 MHz to 108 MHz bands; supports
both RDS and the RBDS standards and programmable
output power.
• Shared Bluetooth and WLAN receive signal
path eliminates the need for an external
power splitter while maintaining excellent
sensitivity for both Bluetooth and WLAN.
• Internal fractional nPLL allows support for a
wide range of reference clock frequencies
General Features
• Supports IEEE 802.15.2 external three-wire
coexistence scheme to optimize bandwidth
utilization with other co-located wireless
technologies such as GPS, WiMax, or UWB
• Supports battery voltage range from 2.3V to 4.8V
supplies with internal switching regulator
• Programmable dynamic power management
• 2 Kbit OTP for storing board parameters
• Package options:
• Supports standard SDIO v2.0 (50 MHz, 4-bit
and 1-bit), and gSPI (48 MHz) host interfaces.
-
-
-
144 ball FCFBGA (6.5 mm x 6.5 mm, 0.5 mm pitch)
133 ball WLBGA (4.89 mm x 5.33 mm, 0.4 mm pitch)
225 bump WLCSP (4.89 mm x 5.33 mm, 0.2 mm
pitch)
• Alternative host interface supports HSIC (a
USB 2.0 derivative for short-distance, on-
board connections).
• Integrated ARM® Cortex-M3 processor and
on-chip memory for complete WLAN
subsystem functionality, minimizing the need
to wake up the applications processor for
standard WLAN functions. This allows for
further minimization of power consumption,
while maintaining the ability to field upgrade
with future features.
• Security:
-
-
-
WPA™- and WPA2™- (Personal) support for powerful
encryption and authentication
AES and TKIP in hardware for faster data encryption
and 802.11i compatibility
Reference WLAN subsystem provides
Cisco® Compatible Extension- (CCX,
CCX 2.0, CCX 3.0, CCX 4.0, CCX 5.0) certified
• OneDriver™ software architecture for easy
migration from existing embedded WLAN and
Bluetooth devices as well as future devices.
-
Reference WLAN subsystem provides Wi-Fi
Protected Setup (WPS)
• Worldwide regulatory support: Global products
supported with worldwide homologated design
BROADCOM
®
August 17, 2011 • 4330-DS206-R
Page 2
10/9/2011 7T5YL
5秒后页面跳转
VIPER22A的资料手册解读、引脚参数说明、代换型号推荐
ADS1256的资料手册解读、采集电压范围、读数变化原因分析及实际测量遇到的问题
MAX6675资料手册参数详解、引脚配置说明
LM258引脚图及功能介绍、主要参数分析
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
