5秒后页面跳转
B39202B4381P810 PDF预览

B39202B4381P810

更新时间: 2022-02-26 15:00:05
品牌 Logo 应用领域
东电化 - TDK /
页数 文件大小 规格书
11页 132K
描述
SAW filters for automotive electronics

B39202B4381P810 数据手册

 浏览型号B39202B4381P810的Datasheet PDF文件第5页浏览型号B39202B4381P810的Datasheet PDF文件第6页浏览型号B39202B4381P810的Datasheet PDF文件第7页浏览型号B39202B4381P810的Datasheet PDF文件第8页浏览型号B39202B4381P810的Datasheet PDF文件第10页浏览型号B39202B4381P810的Datasheet PDF文件第11页 
SAW Components  
SAW 2in1 filter  
Data sheet  
B4381  
1960.0 / 1842.5 MHz  
ESD protection of SAW filters  
SAW filters are Electro Static Discharge sensitive devices. To reduce the probability of damages  
caused by ESD, special matching topologies have to be applied.  
In general, “ESD matching” has to be ensured at that filter port, where electrostatic discharge is  
expected.  
Electrostatic discharges predominantly appear at the antenna input of RF receivers. Therefore  
only the input matching of the SAW filter has to be designed to short circuit or to block the ESD  
pulse.  
Below three figures show recommended “ESD matching” topologies.  
For wideband filters the high-pass ESD matching structure needs to be at least of 3rd order to  
ensure a proper matching for any impedance value of antenna and SAW filter input. The required  
component values have to be determined from case to case.  
Cs1  
Cs3  
Cs1  
Cs3  
to output  
matching  
to output  
matching  
Lp2  
Lp2  
Fig. 1 MLC varistor plus ESD matching  
Fig. 2 Suppressor diode plus ESD matching  
In cases where minor ESD occur, following simplified “ESD matching” topologies can be used  
alternatively.  
Cs1  
Cs3  
to output  
matching  
Lp2  
Fig. 3 3rd order high-pass structure for basic ESD protection  
In all three figures the shunt inductor Lp2 could be replaced by a shorted microstrip with proper  
length and width. If this configuration is possible depends on the operating frequency and  
available pcb space.  
Effectiveness of the applied ESD protection has to be checked according to relevant industry  
standards or customer specific requirements  
For further information, please refer to EPCOS Application report:  
ESD protection for SAW filters”.  
This report can be found under www.epcos.com/rke.Click on “Applications Notes”.  
Please read cautions and warnings and  
important notes at the end of this document.  
9
May 04, 2012  

与B39202B4381P810相关器件

型号 品牌 获取价格 描述 数据表
B39202B4480P810 TDK

获取价格

SAW Components BAW/SAW Duplexer
B39202B5064U410 EPCOS

获取价格

SAW Rx filter WCDMA Band I
B39202B5072U410 TDK

获取价格

SAW Rx filter
B39202B5140U410 EPCOS

获取价格

SAW filter TD-SCDMA
B39202B5142U410 EPCOS

获取价格

SAW filter PCS+G RF Tx filter
B39202B5155U410 EPCOS

获取价格

SAW Components
B39202B5166U410 TDK

获取价格

SAW RF filter for base stations
B39202B5184U410 TDK

获取价格

SAW RF filter for base stations
B39202B5306U410 TDK

获取价格

SAW RF filter for base stations
B39202-B7653-G210 EPCOS

获取价格

SAW Components Low-Loss Dual Band Filter for Mobile Communication 881,5 & 1960,0 MHz