CHIP RESISTOR
(续上页 Continue)
标 准
Specification
试验项目
Test Item
测试方法
Test Method
MIL-STD-202 Method 204
频率:10Hz~2000Hz;加速度:5g’S;一个循环20分钟;X,Y,Z三个
方向每个方向12个循环,共36个循环。
Frequency:10Hz~2000Hz,acceleration:5g’S, a loop 20
min, X,Y,Z three directions, each direction 12 cycles,36
cycles.
无可见损伤
No mechanical damage
振动
Vibration
△
R
≤±(0.1%R+0.05Ω)
AEC-Q200-002
无可见损伤
人体模式,每个电极承受两次放电,正、负极性各1次。
0402:0.5KV;0603:1KV;0805:1.5KV;
1206,1210,2010,2512:2KV
ESD静电放电
Electrostatic
Discharge
No mechanical
damage
≤±(0.5%R+0.05Ω)
△R
Human Body Model,1 pos. + 1 neg discharge.
UL-94
不完全燃尽,薄垫纸应不被引燃,
松木板应不被烤焦炭化
V-0或V-1可接受。不需要电气测试。
V-0 or V-1 are acceptable. Electrical test not
required.
可燃性
Flammability
No ignition of the tissue paper or
scorching or the pinewood board
AEC Q200-006
端子强度
Terminal
Strength
无可见损伤
No mechanical damage
△R≤±(0.1%R+0.05Ω)
施加力: 0402
Appling force 0402:5N,0603~2512:17.7N for
60s 1s
AEC-Q200-001
9Vdc
:5N;0603~2512:17.7N,保持 60s±1s。
±
。
到
32Vdc(钳位电流高达 500A)、增量为1.0Vdc
阻燃性
Flame
Retardant
的电压。每种电压等级最少施加1 小时。
不可燃
Not flame
Subjected to voltage from 9.0 to 32.0 VDC
(current clamped up to 500A),and each voltage
level shall be increased in 1.0 VDC for one hour
minimum
。
JESD22 Method JA-104
-55℃~125℃,高、低温下暴露时间各30min,
转换时间:≤1min,循环次数:1000次.
温度循环
Temperature
Cycling
无可见损伤
No mechanical damage
△R≤±(0.2%R+0.05Ω)
-55℃(30min)~125℃(30min) ,1000 cycles。
MIL-STD-202 Method 103
温度85℃,湿度85%的条件下施加10%额定功率
的电压值或元件极限电压(取较小值),放置
1000小时。
85℃/85%RH. 1000 hours.
Apply 10% of operating power or limiting
element voltage whichever is lower.
高温高湿
Biased
Humidity
无可见损伤
No mechanical damage
△R≤±(0.2%R+0.05Ω)
MIL-STD-202 Method 107
-55℃(15分钟)~常温(≤20 秒)~155℃(15分钟),
300个循环。
无可见损伤
No mechanical damage
△R≤±(0.1%R+0.05Ω)
热冲击
Thermal Shock
-55
≤
℃
(15min)
155
~normal temperature
℃(15min) 300 cycles.
(
20s)
~
,
油浴,恒温105℃±3℃,
放置时间:1000小时
Soaked in industrial oil with sulfur substance
contained in 105℃± , for 1000h.
无可见损伤
No mechanical damage
△R≤±(0.5%R+0.05Ω)
抗硫化
Sulfuration
Resistant
3℃
4