5秒后页面跳转
ATA5830N_14 PDF预览

ATA5830N_14

更新时间: 2022-02-26 13:19:32
品牌 Logo 应用领域
爱特美尔 - ATMEL /
页数 文件大小 规格书
24页 862K
描述
UHF ASK/FSK Transceiver

ATA5830N_14 数据手册

 浏览型号ATA5830N_14的Datasheet PDF文件第7页浏览型号ATA5830N_14的Datasheet PDF文件第8页浏览型号ATA5830N_14的Datasheet PDF文件第9页浏览型号ATA5830N_14的Datasheet PDF文件第11页浏览型号ATA5830N_14的Datasheet PDF文件第12页浏览型号ATA5830N_14的Datasheet PDF文件第13页 
Figure 1-5. Typical 5V Application Circuit with One Wire Control  
VS  
32  
31  
30  
29  
28  
27  
26  
25  
ATEST ATEST  
_IO1 _IO2  
1
2
3
4
24  
23  
PB2  
PB1  
PB0  
RFIN_LB  
RFIN_HB  
RXD  
TXD  
LIN  
GND  
EN  
Atmel  
22  
21  
SPDT_RX  
SPDT_ANT  
ANT_TUNE  
SPDT_TX  
ATA6625  
LIN  
SAW  
DGND  
DVCC  
PC5  
Atmel  
ATA5830  
20  
5
6
19  
18  
NRES  
VCC  
7
8
RF_OUT  
VS_PA  
PC4  
17  
PC3  
VS  
12V  
TEST  
_EN  
Battery  
+
9
10  
11  
12  
13  
14  
15  
16  
VS  
VS = 5V  
Figure 1-5 shows a typical vehicle side application circuit running from a 5V voltage regulator delivered from the LIN  
transceiver ATA6625 device. The application can be directly connected to vehicle's wiring harness. In this case, the pin PB4  
(PWRON) is directly connected to VS and the Atmel® ATA5830 enters the IDLEMode upon power up of the ATA6625 and  
stays there after the software in the Flash asserts the EN pin on ATA6625 to HIGH. The system can be completely switched  
on or off with a command over the one wire bus. This application is used when the external host microcontroller must be  
separated over a distance from the Atmel ATA5830 such as systems having remote antennas integrated into window glass.  
In these situations, the Atmel ATA5830 can work autonomously and communicate to external host microcontroller on a 1  
wire bus.  
The Application software within the 6KB Flash, together with 24KB ROM firmware, is used for the control of the Atmel  
ATA5830 and Atmel ATA6625. A simplified LIN compliant physical layer can be used for one wire communication. The Atmel  
ATA5830 does not natively support one wire commands. However, through the use of application Flash software one wire  
communication can be achieved.  
Please refer to the note in the previous example (Figure 1-4 on page 9) regarding the use of a 4.5 to 5.5V supply and its  
distribution within the Atmel ATA5830. Ports PC0..PC2 have internal 50kΩ pull-up resistors and can be left open. But, ports  
PB1, PB2 and PB5 must be connected to ground. The ANT_Tune pin has to be left open. Notes about RF decoupling and  
supply circuitry are the same as application shown in Figure 1-4 on page 9.  
10  
ATA5830/ATA5830N [SUMMARY DATASHEET]  
9208FS–RKE–06/13  

与ATA5830N_14相关器件

型号 品牌 描述 获取价格 数据表
ATA5830N-PNQW ATMEL Telecom Circuit, 1-Func, 5 X 5 MM, 0.50 MM PITCH, LEAD FREE, VQFN-32

获取价格

ATA5830N-WNQW ATMEL Telecom IC, PQCC32,

获取价格

ATA5830N-WNQW MICROCHIP Telecom IC, PQCC32

获取价格

ATA5830-PLQW ATMEL Telecom Circuit, 1-Func, CMOS, 5 X 5 MM, 0.50 MM PITCH, LEAD FREE, VQFN-32

获取价格

ATA5830-PNQW ATMEL Telecom Circuit, 1-Func, 5 X 5 MM, 0.50 MM PITCH, LEAD FREE, VQFN-32

获取价格

ATA5830-WNQW ATMEL Telecom IC, PQCC32,

获取价格