AS4C1M16S-C&I
Pin Descriptions
Table 3. Pin Details
Symbol
Type
Description
CLK
Input
Clock: CLK is driven by the system clock. All SDRAM input signals are sampled on
the positive edge of CLK. CLK also increments the internal burst counter and
controls the output registers.
CKE
Input
Clock Enable: CKE activates (HIGH) and deactivates (LOW) the CLK signal. If
CKE goes low synchronously with clock (set-up and hold time same as other
inputs), the internal clock is suspended from the next clock cycle and the state of
output and burst address is frozen as long as the CKE remains low. When both
banks are in the idle state, deactivating the clock controls the entry to the Power
Down and Self Refresh modes. CKE is synchronous except after the device enters
Power Down and Self Refresh modes, where CKE becomes asynchronous until
exiting the same mode. The input buffers, including CLK, are disabled during
Power Down and Self Refresh modes, providing low standby power.
A11
Input
Input
Bank Activate: A11 (BA) defines to which bank the BankActivate, Read, Write, or
BankPrecharge command is being applied.
A0-A10
Address Inputs: A0-A10 are sampled during the BankActivate command (row
address A0-A10) and Read/Write command (column address A0-A7 with A10
defining Auto Precharge) to select one location out of the 512K available in the
respective bank. During a Precharge command, A10 is sampled to determine if
both banks are to be precharged (A10 = HIGH). The address inputs also provide
the op-code during a Mode Register Set command.
CS#
Input
Input
Chip Select: CS# enables (sampled LOW) and disables (sampled HIGH) the
command decoder. All commands are masked when CS# is sampled HIGH. CS#
provides for external bank selection on systems with multiple banks. It is
considered part of the command code.
RAS#
Row Address Strobe: The RAS# signal defines the operation commands in
conjunction with the CAS# and WE# signals and is latched at the positive edges of
CLK. When RAS# and CS# are asserted "LOW" and CAS# is asserted "HIGH,"
either the BankActivate command or the Precharge command is selected by the
WE# signal. When the WE# is asserted "HIGH," the BankActivate command is
selected and the bank designated by BA is turned on to the active state. When the
WE# is asserted "LOW," the Precharge command is selected and the bank
designated by BA is switched to the idle state after the precharge operation.
CAS#
WE#
Input
Column Address Strobe: The CAS# signal defines the operation commands in
conjunction with the RAS# and WE# signals and is latched at the positive edges of
CLK. When RAS# is held "HIGH" and CS# is asserted "LOW," the column access
is started by asserting CAS# "LOW." Then, the Read or Write command is
selected by asserting WE# "LOW" or "HIGH."
Input
Input
Write Enable: The WE# signal defines the operation commands in conjunction
with the RAS# and CAS# signals and is latched at the positive edges of CLK. The
WE# input is used to select the BankActivate or Precharge command and Read or
Write command.
LDQM,
UDQM
Data Input/Output Mask: LDQM and UDQM are byte specific, nonpersistent I/O
buffer controls. The I/O buffers are placed in a high-z state when LDQM/UDQM is
sampled HIGH. Input data is masked when LDQM/UDQM is sampled HIGH during
a write cycle. Output data is masked (two-clock latency) when LDQM/UDQM is
sampled HIGH during a read cycle. UDQM masks DQ15-DQ8, and LDQM masks
DQ7-DQ0.
Confidential
4
Rev. 2.0
March /2015
5秒后页面跳转
PCF8574资料解读：主要参数分析、引脚说明
AD637数据手册解读：主要特性、引脚及其功能解读、电气参数
ADUM1201资料手册解读：参数分析、引脚说明、应用分析
一文带你了解压敏电阻器在直流电路中的过压保护作用
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
