Datasheet > AS1326_04

AS1326_04

更新时间： 2022-06-19 22:28:20

品牌	Logo	应用领域
艾迈斯 - AMSCO		转换器升压转换器
页数	文件大小	规格书
19页	1787K
描述
High Current, 0.8A DC-DC Step-Up Converters

阅读下载

中文翻译

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

AS1326_04 数据手册

AS1326

Datasheet - Application Information

Inductor Selection

The AS1326A/AS1326B high switching-frequency allows the use of a small 3.3µH surface-mount inductor. The induc-

tor should generally have a saturation current rating exceeding the N-channel switch current limit; however, it is

acceptable to bias the inductor current into saturation by as much as 20% if a slight reduction in efficiency is accept-

able.

Lower current-rated inductors may be used if ISET is used to reduce the peak inductor current (see Setting the Switch

Current Limit on page 12). For high efficiency, select an inductor with a high-frequency ferrite core material to reduce

core losses. To minimize radiated noise, use a toroid or shielded inductor. Connect the inductor from the battery to the

pin LX as close to the device as possible.

Table 7. Recommended Inductors

Part Number

MOS6020-332

LPS4018-332

DO1608C-272

DCR

46mΩ

80mΩ

Current Rating Dimensions (L/W/T)

Manufacturer

Coilcraft

www.coilcraft.com

3.3µH

2.7µH

1.8A

2.0A

2.1A

6.8x6.0x2.4mm

4x4x1.8mm

6.6x4.45x2.92mm

Sumida

www.sumida.com

CDRH5D18NP-4R1N

4.1µH

57mΩ

1.95A

6x6x2mm

Figure 23. Efficiency vs. IOUT; VIN = 2V, VOUT = 3.3V

Figure 24. Efficiency vs. IOUT; VIN = 3V, VOUT = 5V

MOS6020-332

DO1608C-272

CDRH5D18NP-4R1N

LPS4018-332

MOS6020-332

DO1608C-272

CDRH5D18NP-4R1N

LPS4018-332

0.1

100

1000

0.1

100

1000

Output Current (mA)

External Schottky Diode

For output voltages greater than 4V, an external Schottky diode must be connected between pin LX and POUT, in par-

allel with the integrated synchronous rectifier (see Figure 25). The diode should be rated for 0.5A. An external diode is

also recommended for applications that must start with input voltages at or below 1.8V. The Schottky diode carries cur-

rent during startup and after the synchronous rectifier turns off; thus, its current rating only needs to be 500mA.

Note: Connect the diode as close to the IC as possible.

For circuits that do not require startup with inputs below 1.8V and have an output of 4V or less, the external

diode is not needed.

Caution: Do not use ordinary rectifier diodes as their slow switching speeds and long reverse-recovery times render

them unacceptable.

www.austriamicrosystems.com

Revision 1.05

13 - 18

1...11 12 131415 16 17...19

中文翻译

下载PDF

与AS1326_04相关器件

型号	品牌	获取价格	描述	数据表
AS1326_1	AMSCO	获取价格	High Current, 0.8A DC-DC Step-Up Converters
AS1326A	AMSCO	获取价格	High Current, 0.8A DC-DC Step-Up Converters
AS1326A-BTDR	AMSCO	获取价格	High Current, 0.8A DC-DC Step-Up Converters
AS1326A-BTDT	AMSCO	获取价格	High Current, 0.8A DC-DC Step-Up Converters
AS1326B	AMSCO	获取价格	High Current, 0.8A DC-DC Step-Up Converters
AS1326B-BTDR	AMSCO	获取价格	High Current, 0.8A DC-DC Step-Up Converters
AS1326B-BTDT	AMSCO	获取价格	High Current, 0.8A DC-DC Step-Up Converters
AS1329	AMSCO	获取价格	Low Voltage, Micropower, DC-DC Step-Up Converters
AS1329_1	AMSCO	获取价格	Low Voltage, Micropower, DC-DC Step-Up Converters
AS1329_13	AMSCO	获取价格	Low Vol tage, Micropower, DC-DC Step-Up Conver ters

与AS1326_04相关文章

压敏电阻器在直流电路中的过压保护应用探讨
2024-06-07

2
电感耐压值及其与电感大小的关系
2024-06-07

5
CNY17F光耦合器：特性、应用、封装、引脚功能及替换型号解析
2024-06-07

4
DS1307资料解析：特性、引脚说明、替代推荐
2024-06-07

3

产品中心

服务支持

精选活动

关于我们

帮助中心

AS1326_04

AS1326_04 数据手册

与AS1326_04相关器件

与AS1326_04相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

AS1326_04

AS1326_04 数据手册

与AS1326_04相关器件

与AS1326_04相关文章

您还可以找

您在本页遇到什么问题？