Datasheet > AS1326

AS1326

更新时间： 2024-02-01 02:33:00

品牌	Logo	应用领域
艾迈斯 - AMSCO		转换器升压转换器
页数	文件大小	规格书
18页	1038K
描述
High Current, 0.8A DC-DC Step-Up Converters

阅读下载

中文翻译

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

AS1326 技术参数

生命周期：	Obsolete	Reach Compliance Code：	unknown
风险等级：	5.82	Base Number Matches：	1

AS1326 数据手册

AS1326

Data Sheet - Application Information

Inductor Selection

The AS1326A/AS1326B high switching-frequency allows the use of a small 3.3µH surface-mount inductor. The induc-

tor should generally have a saturation current rating exceeding the N-channel switch current limit; however, it is

acceptable to bias the inductor current into saturation by as much as 20% if a slight reduction in efficiency is accept-

able.

Lower current-rated inductors may be used if ISET is used to reduce the peak inductor current (see Setting the Switch

Current Limit on page 12). For high efficiency, select an inductor with a high-frequency ferrite core material to reduce

core losses. To minimize radiated noise, use a toroid or shielded inductor. Connect the inductor from the battery to the

pin LX as close to the device as possible.

Table 7. Recommended Inductors

Part Number

MOS6020-332

LPS4018-332

DO1608C-272

DCR

46mΩ

80mΩ

Current Rating Dimensions (L/W/T)

Manufacturer

Coilcraft

www.coilcraft.com

3.3µH

2.7µH

1.8A

2.0A

2.1A

6.8x6.0x2.4mm

4x4x1.8mm

6.6x4.45x2.92mm

Sumida

www.sumida.com

CDRH5D18NP-4R1N

4.1µH

57mΩ

1.95A

6x6x2mm

Figure 23. Efficiency vs. IOUT; VIN = 2V, VOUT = 3.3V

Figure 24. Efficiency vs. IOUT; VIN = 3V, VOUT = 5V

MOS6020-332

DO1608C-272

CDRH5D18NP-4R1N

LPS4018-332

MOS6020-332

DO1608C-272

CDRH5D18NP-4R1N

LPS4018-332

0.1

100

1000

0.1

100

1000

Output Current (mA)

External Schottky Diode

For output voltages greater than 4V, an external Schottky diode must be connected between pin LX and POUT, in par-

allel with the integrated synchronous rectifier (see Figure 25). The diode should be rated for 0.5A. An external diode is

also recommended for applications that must start with input voltages at or below 1.8V. The Schottky diode carries cur-

rent during startup and after the synchronous rectifier turns off; thus, its current rating only needs to be 500mA.

Note: Connect the diode as close to the IC as possible.

For circuits that do not require startup with inputs below 1.8V and have an output of 4V or less, the external

diode is not needed.

Caution: Do not use ordinary rectifier diodes as their slow switching speeds and long reverse-recovery times render

them unacceptable.

www.austriamicrosystems.com

Revision 1.02

13 - 18

1...10 11 121314 15 16...18

中文翻译

下载PDF

与AS1326相关器件

型号	品牌	描述	获取价格	数据表
AS1326_04	AMSCO	High Current, 0.8A DC-DC Step-Up Converters	获取价格
AS1326_1	AMSCO	High Current, 0.8A DC-DC Step-Up Converters	获取价格
AS1326A	AMSCO	High Current, 0.8A DC-DC Step-Up Converters	获取价格
AS1326A-BTDR	AMSCO	High Current, 0.8A DC-DC Step-Up Converters	获取价格
AS1326A-BTDT	AMSCO	High Current, 0.8A DC-DC Step-Up Converters	获取价格
AS1326B	AMSCO	High Current, 0.8A DC-DC Step-Up Converters	获取价格