AH1894
Absolute Maximum Ratings (Note 6) (@TA = +25°C, unless otherwise specified.)
Symbol
VDD
Parameter
Rating
6
Unit
V
Supply Voltage (Note 7)
Reverse Supply Voltage
Output current (source and sink)
Magnetic Flux Density
-0.3
3.5
V
VDD_REV
IOUTPUT
B
mA
Unlimited
X1-DFN1216-4
SOT553
230
mW
mW
°C
Package Power Dissipation
PD
230
Ts
TJ
Storage Temperature Range
-65 to +150
Maximum Junction Temperature
150
8
°C
VDD, GND and OUTPUT pins
BSEL pin
kV
ESD HBM
Human Body Model (HMB) ESD capability
6
kV
Notes:
6. Stresses greater than the 'Absolute Maximum Ratings' specified above may cause permanent damage to the device. These are stress ratings only;
functional operation of the device at these or any other conditions exceeding those indicated in this specification is not implied. Device reliability may be
affected by exposure to absolute maximum rating conditions for extended periods of time.
7. The absolute maximum VDD of 6V is a transient stress rating and is not meant as a functional operating condition. It is not recommended to
operate the device at the absolute maximum rated conditions for any period of time.
Recommended Operating Conditions (@TA = +25°C, unless otherwise specified.)
Symbol
VDD
Parameter
Supply Voltage
Operating Temperature Range
Conditions
Rating
Unit
V
Operating
Operating
1.6V to 3.6V
-40 to +85
°C
TA
Electrical Characteristics (@TA = +25°C, VDD = 1.85V, unless otherwise specified.)
Symbol
VOL
Parameter
Conditions
Min
Typ
0.1
Max
0.2
—
Unit
Output Low Voltage (on)
IOUT = 1mA
IOUT = -1mA
—
V
V
VOH
Output High Voltage (off)
VDD -0.2
VDD -0.1
< 0.1
—
Ioff
Output Leakage Current
VOUT = 3.6V, Output off
-
0
1
µA
V
VSEL_LB
VSEL_HB
RPD_BSEL
BSEL pin input voltage – Low Band
BSEL pin input voltage – High Band
0.5
3.6
—
1.4
—
—
V
BSEL pin internal pull-down resistor (Note 8)
During ‘awake’ period,
A = +25°C, VDD = 3V
50
kΩ
—
—
2.1
2.5
—
—
mA
mA
IDD(awake)
IDD(sleep)
T
Supply Current
During ‘sleep’ period,
TA = +25°C, VDD = 3V
—
—
—
—
—
4.3
7.2
50
8
µA
µA
µs
ms
%
TA = +25°C, VDD = 1.85V
TA = +25°C, VDD = 3.6V
(Note 9)
Average Supply Current
IDD(avg)
13
Tawake
Tperiod
D.C.
Awake Time
Period
100
100
—
(Note 9)
50
Duty Cycle
(Note 10)
0.1
Notes:
8. BSEL pin internal pull-down resistor is only active during AWAKE time
9. When power is initially on, the operating VDD (1.6V to 3.6V) must be applied to guarantee the output sampling.
The output state is valid after the second operating phase (typical 100ms).
10. Transition time varies dependant on the timing of BSEL activation during the sleep and awake phases.
3 of 13
www.diodes.com
July 2013
© Diodes Incorporated
AH1894
Document number: DS35741 Rev. 1 - 2