Datasheet > ADL5360XCPZ-WP

ADL5360XCPZ-WP

更新时间： 2024-01-11 10:44:19

品牌	Logo	应用领域
亚德诺 - ADI		放大器
页数	文件大小	规格书
9页	479K
描述
Dual 900MHz Balanced Mixer with Low Side LO Buffer, IF Amp, and RF Balun

阅读下载

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

ADL5360XCPZ-WP 技术参数

是否Rohs认证：	符合	生命周期：	Obsolete
零件包装代码：	QFN	包装说明：	6 X 6 MM, LFCSP-36
针数：	36	Reach Compliance Code：	compliant
HTS代码：	8542.39.00.01	风险等级：	5.84
JESD-30 代码：	S-XQCC-N36	长度：	6 mm
功能数量：	1	端子数量：	36
最高工作温度：	85 °C	最低工作温度：	-40 °C
封装主体材料：	UNSPECIFIED	封装代码：	HVQCCN
封装形状：	SQUARE	封装形式：	CHIP CARRIER, HEAT SINK/SLUG, VERY THIN PROFILE
认证状态：	Not Qualified	座面最大高度：	1 mm
标称供电电压：	3.3 V	表面贴装：	YES
技术：	BICMOS	电信集成电路类型：	RF FRONT END CIRCUIT
温度等级：	INDUSTRIAL	端子形式：	NO LEAD
端子节距：	0.5 mm	端子位置：	QUAD
宽度：	6 mm	Base Number Matches：	1

ADL5360XCPZ-WP 数据手册

ADL5360

Preliminary Technical Data

Table 3. Eval Board Configuration

Components

Function

Default Conditions

C1, C4, C5, C8, C10, C12,

C13, C15, C18, C21, C22,

C23, C24, C25, C26

Power Supply Decoupling. Nominal supply decoupling consists a

0.01 μF capacitor to ground in parallel with 10pF capacitors to

ground positioned as close to the device as possible.

C10 = 4.7 μF (size 3216)

C1, C8, C12, C21 = 150pF (size 0402)

C4, C5, C22, C23, C24, C25, C26 = 10pF

(size 0402)

C13, C15, C18 = 0.1 μ (size 0402)

C2, C7 = 10pF (size 0402)

C3, C6 = 0.01 μF (size 0402)

C9, C22 = 22pF (size 0402)

Z1-Z4 = open (size 0402)

Z1-Z4, C2, C3, C6, C7, C9,

C22

RF Main and Diversity Input Interface. Main and Diversity input

channels are ac-coupled through C9 and C22. Z1-Z4 provides

additional component placement for external matching/filter

networks. C2, C3, C6, and C7 provide bypassing for the center taps

of the main and diversity on-chip input baluns.

T1, T2, C17, C19, C20, C27, IF Main and Diversity Output Interface. The open collector IF output

C17, C19, C20, C29-C33 = 0.001 μF (size

C28, C29, C30, C31, C32,

C33, L1, L2, L4, L5, R3, R6,

R9, R10

interfaces are biased through pull-up choke inductors L1, L2, L4, and 0402)

L5, with R3 and R6 available for additional supply bypassing. T1 and

T2 are 4:1 impedance transformers used to provide a single ended IF

output interface, with C27 and C28 providing center-tap bypassing.

C17, C19, C20, C29, C30, C31, C32, and C33 ensure an ac-coupled

output interface. R9 and R10 should be removed for balanced

output operation.

C27, C28 = 150pF (size 0402)

T1, T2 = TC4-1T+ (MiniCircuits)

L1, L2, L4, L5 = 330 nH (size 0805)

R3, R6, R9, R10 = 0 Ω (size 0402)

C14, C16, R15, LOSEL

LO Interface. C14 and C16 provide ac-coupling for the LOI1 and LOI2 C14, C16 = 10pF (size 0402)

local oscillator inputs. LOSEL selects the appropriate LO input for

both mixer cores. R15 provides a pull-down to ensure LOI2 is

enabled when the LOSEL jumper is removed. Jumper can be

removed to allow LOSEL interface to be excercised using external

logic generator.

R15 = 10kΩ (size 0402)

LOSEL = 2-pin shunt

R19, PWDN

PWDN Interface. When the PWDN 2-pin shunt is inserted the

ADL5356 is powered down. When open R19 pulls the PWDN logic

low and enables the device. Jumper can be removed to allow PWDN

interface to be excercised using external logic generator. It is

permissible to ground the pwrdn pin for nominal operation.

R19 = 10kΩ (size 0402)

PWDN = 2-pin shunt

R1, R2, R4, R5,L3, L6, R7,

R8, R11, R12, R13, R14,

R16, R17, C34

Bias Control. R16 and R17 form a voltage divider to provide a 3V for

logic control, bypassed to ground through C34. R7, R8, R11, R12,

R13, and R14 provide resistor programmability of VGS0, VGS1 and

VGS2. Typically these nodes can be hard-wired for nominal

operation. It is permissible to ground these pins for nominal

operation. R2 and R5 set the bias point for the internal LO buffers. R1

and R4 set the bias point for the internal IF amplifiers. L3 and L6 are

external inductors used to improve isolation and common mode

rejection.

R1, R4 = 1.2kΩ (size 0402)

R2, R5 = 390Ω (size 0402)

L3, L6 = 10nH (size 0603)

R7, R13, R14 = open (size 0402)

R8, R11, R12 = 0Ω (size 0402)

R16 = 10kΩ (size 0402)

R17 = 15kΩ (size 0402)

C34 = 1nF (size 0402)

REV. PrA | Page 8 of 9

1...5 6 789

下载PDF

与ADL5360XCPZ-WP相关器件

型号	品牌	描述	获取价格	数据表
ADL5363	ADI	2300 MHz to 2900 MHz Balanced Mixer	获取价格
ADL5363ACPZ-R7	ADI	2300 MHz to 2900 MHz Balanced Mixer	获取价格
ADL5363-EVALZ	ADI	2300 MHz to 2900 MHz Balanced Mixer	获取价格
ADL5365	ADI	1200 MHz to 2500 MHz Balanced Mixer, LO Buffer and RF Balun	获取价格
ADL5365ACPZ-R7	ADI	1200 MHz to 2500 MHz Balanced Mixer, LO Buffer and RF Balun	获取价格
ADL5365-EVALZ	ADI	1200 MHz to 2500 MHz Balanced Mixer, LO Buffer and RF Balun	获取价格

与ADL5360XCPZ-WP相关文章

CP2102资料手册解读：CP2102引脚说明、关键参数分析
2024-05-23

1
资料手册解读：UC3842参数和管脚说明
2024-05-22

5
一文带你了解无源晶振的负载电容为何要加两颗谐振电容CL1和CL2
2024-05-22

4
玻璃管保险丝与陶瓷管保险丝：区别与替代性探讨
2024-05-22

3

产品中心

服务支持

精选活动

关于我们

帮助中心

ADL5360XCPZ-WP

ADL5360XCPZ-WP 技术参数

ADL5360XCPZ-WP 数据手册

与ADL5360XCPZ-WP相关器件

与ADL5360XCPZ-WP相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

ADL5360XCPZ-WP

ADL5360XCPZ-WP 技术参数

ADL5360XCPZ-WP 数据手册

与ADL5360XCPZ-WP相关器件

与ADL5360XCPZ-WP相关文章

您还可以找

您在本页遇到什么问题？