Energy Metering Chipset for Polyphase
Shunt Meters
Preliminary Technical Data
ADE7978/ADE7933/ADE7932
Operating temperature: −40°C to +85°C
FEATURES
Flexible I2C, SPI, and HSDC serial interfaces
Enables shunt current sensors in polyphase energy meters
Immune to magnetic tampering
Highly accurate; supports EN 50470-1, EN 50470-3,
IEC 62053-21, IEC 62053-22, IEC 62053-23, ANSI C12.20
and IEEE1459 standards
APPLICATIONS
Energy metering systems
Power monitoring
Compatible with 3-phase, 3- or 4-wire (delta or wye), and
other 3-phase services
Computes active, reactive, and apparent energy, on each
phase and on the overall system
GENERAL DESCRIPTION
The ADE7978 and ADE7933/ADE7932 form a chipset
dedicated to measuring 3-phase electrical energy measurement
using shunts as current sensors.
Less than 0.25% error in active and reactive energy over a
dynamic range of 2000 to 1 at TA = 25°C
Less than 0.1% error in voltage and current rms over a
dynamic range of 1000 to 1 at TA = 25°C
Power quality measurements including THD
Wide-supply voltage operation: 2.4 V to 3.7 V
Reference: 1.2 V (drift 10 ppm/°C typical)
Single 3.3 V supply
Safety and regulatory approvals
UL recognition
5000 Vrms for 1 minute per UL 1577
CSA Components Acceptance Notice #5A
IEC 61010-1: 400V rms (basic)
The ADE7933/ADE7932 is an isolated three-input channel,
analog to digital converter (ADC) for polyphase energy
metering applications using shunt current sensors. It features
three 24-bit analog to digital converters, each of which provides
70dB signal to noise ratio over a 3 kHz signal bandwidth. One
channel is dedicated to measuring the voltage across a shunt
when the shunt is used for current sensing. Two additional
channels are dedicated to measuring voltages, which are usually
sensed using resistor dividers. The ADE7933 and ADE7932 also
measure the temperature of the IC. The ADE7932 is the same as
the ADE7933 but it does not include the second voltage
measurement.
VDE Certificate of Conformity
(continues on next page)
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12
V
IORM = 846 V peak
ISOLATION
BARRIER
Neutral Phase A Phase B Phase C
3.3V
3.3V
3.3V
3.3V
V1P
VM
IM
Phase A
ADE7933/
ADE7932
IP
V2P
GNDISO_A
GNDMCU
V1P
VM
IM
Phase B
ADE7933/
ADE7932
3.3V
3.3V
IP
V2P
ADE7978
ENERGY
I2C/HSDC or SPI
SYSTEM
MICROCONTROLLER
GNDISO_B
GNDMCU
METERING
IC
V1P
VM
IM
IRQ0, IRQ1
Phase C
ADE7933/
ADE7932
GNDMCU
GNDMCU
IP
V2P
GNDISO_C
GNDMCU
V1P
VM
IM
Neutral
line
ADE7933/
ADE7932
(OPTIONAL)
IP
V2P
Load
GNDISO_N
GNDMCU
EARTH
Figure 1. 3 Phase 4 Wire Meter with Four ADE7933/ADE7932s and One ADE7978
Rev. PrF
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2013 Analog Devices, Inc. All rights reserved.