CHIP RESISTOR
标 准
Specifications
项目
测试方法
Item
Test Methods
片式电阻器
Resistor
跨接电阻
Jumper
无可见损伤
No mechanical damage
无可见损伤
No mechanical damage
AEC-Q200 Test 16/MIL-STD-202 Method 107
-55℃(15分钟)~常温(
≤
20秒)~155℃(15分钟),300个循环。
热冲击
Thermal Shock
0.5%
、1%:
F
级:0201
0402及以上
:
:
R
R
≤
≤
35 m
10 m
50 m
Ω
Ω
≤
-55℃(15min)~normal temperature( 20s)~155℃
△R
≤±(0.5%R
+
0.05
Ω
Ω
)
)
(15min) ,300 cycles.
5%
:
J
级
:R
≤
Ω
△R≤±(1.0%R
+
0.05
无可见损伤
No mechanical damage
AEC-Q200 Test 17/AEC-Q200-002
ESD 静电放电
Electrostatic
Discharge
(ESD)
无可见损伤
No mechanical damage
≤±(3.0%R 0.05
人体模式,两次放电,正、负极性各1次
。
F
级:0201
:
:
R
R
≤
≤
35 m
10 m
50 m
Ω
Ω
Human body model, 1pos + 1neg. discharges.
0201:0.5kV;0402/0603:1kV ;0508:1.5kV;
0805/0612/1225:2kV;1206/1210/2010/2512:3kV.
0402及以上
△R
+
Ω)
J级
:R≤
Ω
无可见损伤
No mechanical damage
可焊面积 95%
95% Cover Min
AEC-Q200 Test 18/IEC 60115-1 4.17
可焊性
Solderability
245℃±
5℃锡槽,保持3s±0.3s.
≥
Lead-free solder bath at 245℃±
5℃ for 3s±0.3s.
AEC-Q200 Test 19/IEC 60115-1 4.8
+20℃/-55℃/+20℃/+125℃/+20℃
在规定值内
Within specified T.C.R
电阻温度系数
/
T.C.R
AEC-Q200 Test 20/UL-94
不完全燃尽,薄垫纸应不被引燃,
松木板应不被烤焦炭化。
No ignition of the tissue paper or
scorching or the pinewood board.
可燃性
Flammability
V-0或V-1可接受。不需要电气测试。
V-0 or V-1 are acceptable. Electrical test not
required.
无可见损伤
无可见损伤
AEC-Q200 Test 21/AEC-Q200-005
No mechanical damage
弯曲距离(Bending distance)
:
基板弯曲试验
Substrate
Bending Test
No mechanical damage
0.5%、1%:
0201
1206
2010
、
、
、
0402
1210:4mm;0508:3mm;
2512 0612:2mm;1225:1mm
60s±5s
、0603、0805:5mm;
F
级:0201
:
R
≤
35 m
10 m
50 m
Ω
Ω
△
R
≤±(0.5%R
+
+
0.05
0.05
Ω
)
)
0402及以上
:
R≤
5%
:
、
J级
:R≤
Ω
△R≤±(1.0%R
Ω
保持时间(Duration)
:
AEC-Q200 Test 22/AEC-Q200-006
0201施加力:2N,保持60±1秒。
0402施加力:5N,保持60±1秒。
无可见损伤
No mechanical damage
无可见损伤
No mechanical damage
端子强度
Terminal
Strength
0603及以上施加力: 17.7N,保持 60±1秒。
0.5%、1%:
F
级:0201
:
R
≤
35 m
10 m
50 m
Ω
For 0201:Appling force 2N for 60s
For 0402:Appling force 5N for 60s
±
±
1s.
1s.
△R
≤±(0.5%R
+
0.05
0.05
Ω
)
)
0402及以上
:R
≤
Ω
5%
:
J级
:R≤
Ω
For 0603 and above size:Appling force 17.7N for 60s±1s.
△R≤±(1.0%R
+
Ω
AEC-Q200 Test 24/AEC-Q200-001
9Vdc 到 32Vdc(钳位电流高达 500A)、增量为 1.0Vdc
的电压。每种电压等级最少施加1小时。
阻燃性
Flame
Retardance
不可燃
No flame
Subjected to voltage from 9.0 to 32.0 VDC(current
clamped up to 500A), and each voltage level shall be
increased in 1.0 VDC for one hour minimum.
IEC 60115-1 4.6
在电极与基片间施加100V±15V直流电压,保持1分钟,
然后测绝缘电阻值。
绝缘电阻
Insulation
Resistance
1000MΩ Min
Apply DC 100V±15V between substrate and
terminations for 1min, then check insulation resistance.
IEC 60115-1 4.7
在电极与基片间以大约100V/s的速率施加有效值为最大过
无击穿或飞弧
No breakdown or flashover
耐电压
Voltage Proof
负荷电压的交流电压,保持60s±5s。
Apply max. overload voltage of AC RMS at a rate of
approximately 100V/s between substrate and terminations
for 60s±5s.
无可见损伤
No mechanical damage
无可见损伤
No mechanical damage
级:0201 35 m
0402及以上 10 m
IEC 60115-1 4.13
0.5% 1%
、
:
短时间过负载
Short Time
Overload
F
:
:
R
R
≤
≤
Ω
Ω
2.5倍额定电压或最大过负荷电压/电流(取较小值),持续
2.5 times rated voltage or max. overload voltage
(current)whichever is lower for 5s.
5秒。
△
5%
R
:
≤±(1.0%R
+0.05
Ω
)
)
J
级
:R
≤50 m
Ω
△R≤±(2.0%R+0.05
Ω
7