5秒后页面跳转
AD8022AR-REEL7 PDF预览

AD8022AR-REEL7

更新时间: 2024-02-01 04:24:06
品牌 Logo 应用领域
亚德诺 - ADI 运算放大器放大器电路光电二极管
页数 文件大小 规格书
16页 373K
描述
Dual High Speed, Low Noise Op Amp

AD8022AR-REEL7 技术参数

是否无铅: 含铅是否Rohs认证: 不符合
生命周期:Obsolete零件包装代码:SOIC
包装说明:MS-012AA, SOIC-8针数:8
Reach Compliance Code:not_compliantECCN代码:EAR99
HTS代码:8542.33.00.01风险等级:5.1
Is Samacsys:N放大器类型:OPERATIONAL AMPLIFIER
架构:VOLTAGE-FEEDBACK最大平均偏置电流 (IIB):7.5 µA
25C 时的最大偏置电流 (IIB):5 µA标称共模抑制比:98 dB
频率补偿:YES最大输入失调电压:6250 µV
JESD-30 代码:R-PDSO-G8JESD-609代码:e0
长度:4.9 mm低-偏置:NO
低-失调:NO微功率:NO
湿度敏感等级:1负供电电压上限:-13.2 V
标称负供电电压 (Vsup):-2.5 V功能数量:2
端子数量:8最高工作温度:85 °C
最低工作温度:-40 °C封装主体材料:PLASTIC/EPOXY
封装代码:SOP封装等效代码:SOP8,.25
封装形状:RECTANGULAR封装形式:SMALL OUTLINE
包装方法:TAPE AND REEL峰值回流温度(摄氏度):240
功率:NO电源:+-2.5/+-12 V
可编程功率:NO认证状态:Not Qualified
座面最大高度:1.75 mm最小摆率:30 V/us
标称压摆率:42 V/us子类别:Operational Amplifier
最大压摆率:12.2 mA供电电压上限:13.2 V
标称供电电压 (Vsup):2.5 V表面贴装:YES
技术:BIPOLAR温度等级:INDUSTRIAL
端子面层:Tin/Lead (Sn85Pb15)端子形式:GULL WING
端子节距:1.27 mm端子位置:DUAL
处于峰值回流温度下的最长时间:30标称均一增益带宽:10000 kHz
宽带:YES宽度:3.9 mm
Base Number Matches:1

AD8022AR-REEL7 数据手册

 浏览型号AD8022AR-REEL7的Datasheet PDF文件第10页浏览型号AD8022AR-REEL7的Datasheet PDF文件第11页浏览型号AD8022AR-REEL7的Datasheet PDF文件第12页浏览型号AD8022AR-REEL7的Datasheet PDF文件第13页浏览型号AD8022AR-REEL7的Datasheet PDF文件第14页浏览型号AD8022AR-REEL7的Datasheet PDF文件第16页 
AD8022  
6800pF  
5% NPO  
LAYOUT CONSIDERATIONS  
As is the case with all high speed amplifiers, careful attention to  
printed circuit board layout details prevent associated board  
parasitics from becoming problematic. Proper RF design  
technique is mandatory. The PCB should have a ground plane  
covering all unused portions of the component side of the  
board to provide a low impedance return path. Removing the  
ground plane from the area near the input signal lines reduces  
stray capacitance. Chip capacitors should be used for supply  
bypassing. One end of the capacitor should be connected to the  
ground plane, and the other should be connected no more than  
1/8 inch away from each supply pin. An additional large  
(0.47 μF to 10 μF) tantalum capacitor should be connected in  
parallel, although not necessarily as close, in order to supply  
current for fast, large signal changes at the AD8022 output.  
Signal lines connecting the feedback and gain resistors should  
be as short as possible, minimizing the inductance and stray  
capacitance associated with these traces. Locate termination  
resistors and loads as close as possible to the input(s) and  
output, respectively. Adhere to stripline design techniques for  
long signal traces (greater than about 1 inch). Following these  
generic guidelines improves the performance of the AD8022 in  
all applications.  
12V  
8
191Ω  
243Ω  
1%  
1%  
AD8022  
3
2
+V  
IN  
1
+V  
OUT  
8200pF  
10%  
249Ω  
1%  
422Ω  
COMMON-  
MODE  
VOLTAGE  
SIGNAL C LEVEL  
M
1%  
0.1μF  
16V  
10%  
0.1μF  
50V  
5%  
249Ω  
1%  
X7R  
NPO  
8200pF  
10%  
6
5
7
–V  
OUT  
–V  
IN  
AD8022  
4
191Ω  
1%  
243Ω  
1%  
6800pF  
5% NPO  
Figure 41. Differential Input Sallen-Key Filter  
Using AD8022 on Single Supply, +12 V  
7.5  
2.5  
–2.5  
–7.5  
–12.5  
–17.5  
–22.5  
–27.5  
–32.5  
–37.5  
–42.5  
10k  
100k  
FREQUENCY (Hz)  
1M  
10M  
Figure 42. Frequency Response of Sallen-Key Filter  
Rev. B | Page 15 of 16  
 

与AD8022AR-REEL7相关器件

型号 品牌 描述 获取价格 数据表
AD8022ARZ ADI Dual High Speed, Low Noise Op Amp

获取价格

AD8022ARZ-REEL ADI Dual High Speed, Low Noise Op Amp

获取价格

AD8022ARZ-REEL7 ADI Dual High Speed, Low Noise Op Amp

获取价格

AD8023 ADI High Current Output, Triple Video Amplifier

获取价格

AD8023ACHIPS ADI High Current Output, Triple Video Amplifier

获取价格

AD8023AR ADI High Current Output, Triple Video Amplifier

获取价格