A7D-206

更新时间： 2024-02-29 01:16:57

品牌	Logo	应用领域
欧姆龙 - OMRON		开关指轮滚轮开关按动滚轮开关
页数	文件大小	规格书
5页	495K
描述
Ultra-small, Low-cost, Push-operated Switches

阅读下载

中文翻译

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

A7D-206 技术参数

生命周期：	Active	Reach Compliance Code：	unknown
ECCN代码：	EAR99	HTS代码：	8536.50.70.00
Factory Lead Time：	8 weeks 3 days	风险等级：	5.75
Is Samacsys：	N	执行器角度：
执行器长度：	0.146 inch	执行器类型：	PUSHBUTTON
其他特性：	PANEL MOUNTABLE	主体宽度：	16 mm
本体颜色：	GRAY	主体高度：	17.5 mm
主体长度或直径：	55.9 mm	喷头长度：
最大触点电流（直流）：	0.1 A	触点（直流）最大额定R负载：	.1A@30VDC
触点功能：	BINARY CODED	触点电阻：	0.2 m Ω
触点时间：	BREAK-BEFORE-MAKE	最大触点电压（直流）：	30 V
介质耐电压：	1000VAC V	电气寿命：	20000 Cycle(s)
绝缘电阻：	100000000 Ω	安装特点：	THROUGH HOLE-STRAIGHT
位置数：	10	开关段数量：	1
最高工作温度：	70 °C	最低工作温度：	-10 °C
表面贴装：	NO	开关动作：	MOMENTARY
开关功能：	BINARY CODED DECIMAL	开关类型：	THUMB/PUSHWHEEL SWITCH
端子长度：	0.146 inch	端接类型：	SOLDER
Base Number Matches：	1

A7D-206 数据手册

A7D/A7DP

Ordering Procedure

Place orders as shown in the example below, specifying the model and number.

1. A7D-2M (End Caps): 1 pair

2. A7D-206-S@@ (Switch Unit with stopper): 1 piece

3. A7D-206 (Switch Unit): 1 piece

4. A7D-2P@ (Spacer): 1 piece

5. A7D-206 (Switch Unit): 2 pieces

Note: Standard products, such as the Switch Units and End Caps, are not factory-assembled for shipment. Contact your OMRON representative for details on ordering

factory-assembled sets.

Safety Precautions

Refer to Safety Precautions for All Thumbwheel Switches.

Precautions for Correct Use

Handling

Soldering

• The molded components of the Switch use polyacetal resin and

PBT resin. It is recommended that alcohol is used to wipe off dirt

and smudges from the molded components. Take care to prevent

the alcohol from getting inside.

• Do not use thinner or other solutions which might damage the resin.

• Terminals can withstand a force of 4.9 N for 10 seconds or more

(the mating strength of the case and seal), and survive bending of

20° without breaking after returning to original position. Do not use

excessive force or apply repetitive external force, however, when

handling terminals. In particular, take care to avoid dropping them

as the terminals might bend or break.

• Using a Soldering Iron

Use a 30-W soldering iron at a temperature of 350°C for a maximum

of 3 seconds, and flush as described above.

Do not apply force to the terminals during soldering and for 3 minutes

after soldering is completed. Doing so may result in conduction or

operation failure.

Ensure that soldering flux and alcohol do not penetrate into the Switch

interior

Setting Numbers

Pen-push Type

Press the setting switch with the tip of a ball-point pen. Do not use

pencil point or mechanical pencil point to press the setting switch,

otherwise the lead of the pencil or mechanical pencil may be broken

and A7DP malfunctions may result due to fragments of the broken

lead.

• The setting buttons can withstand 19.6 N for 1 minute, but do not

push the (+) and (-) buttons at the same time.

Screw-mounting Models

Tighten mounting screws to a torque between 0.2 to 0.24 N·m, using

M2.6 screws. Use plain washers or spring washers together with the

screws.

1 2 345

中文翻译

下载PDF

与A7D-206相关器件

型号	品牌	描述	获取价格	数据表
A7D-206-1	OMRON	Ultra-small, Low-cost, Push-operated Switches	获取价格
A7D-2M	OMRON	Analog Circuit	获取价格
A7D-2M-1	OMRON	Analog Circuit	获取价格
A7D-2PA	OMRON	Analog Circuit	获取价格
A7D-2PA-1	OMRON	Analog Circuit	获取价格
A7DP-206	OMRON	Ultra-small, Low-cost, Push-operated Switches	获取价格
A7DP-206-1	OMRON	Ultra-small, Low-cost, Push-operated Switches	获取价格
A7F01	SWITCH	A SERIES FEMALE QG	获取价格
A7F02	SWITCH	A SERIES FEMALE QG	获取价格
A7F03	SWITCH	Audio/RCA Connector, 7 Pole(s), Solder Terminal,	获取价格

与A7D-206相关文章

晶闸管阳极与阴极之间加电压时控制极的电流流动分析
2024-06-05

6
探究MOS管沟道夹断后载流子传输机制及其电路设计影响
2024-06-05

6
光敏电阻的工作原理、作用及检测方法
2024-06-05

4
ENC28J60以太网控制器全面解析：特性、应用、引脚说明
2024-06-05

2

产品中心

服务支持

精选活动

关于我们

帮助中心

A7D-206

A7D-206 技术参数

A7D-206 数据手册

与A7D-206相关器件

与A7D-206相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

A7D-206

A7D-206 技术参数

A7D-206 数据手册

与A7D-206相关器件

与A7D-206相关文章

您还可以找

您在本页遇到什么问题？