A1308 and
A1309
Linear Hall-Effect Sensor ICs with Analog Output
Available in a Miniature, Low-Profile Surface-Mount Package
is defined as:
The output voltage clamps, VCLPHIGH and VCLPLOW, limit the
operating magnetic range of the applied field in which the device
provides a linear output. The maximum positive and negative
applied magnetic fields in the operating range can be calculated:
SensTA – SensIDEAL(TA)
∆SensTC
=
100 (%)
×
(5)
SensIDEAL(TA)
Sensitivity Drift Due to Package Hysteresis. Package
VCLPHIGH – VOUT(Q)
stress and relaxation can cause the device sensitivity at TA = 25°C
to change during and after temperature cycling. This change in
sensitivity follows a hysteresis curve. For purposes of specifica-
BMAX(+)
=
=
(10)
Sens
VOUT(Q) – VCLPLOW
BMAX(–)
tion, the Sensitivity Drift Due to Package Hysteresis, ∆SensPKG
,
Sens
is defined as:
Sens(25°C)(2) – Sens(25°C)(1)
Symmetry Sensitivity Error. The magnetic sensitivity of the
device is constant for any two applied magnetic fields of equal
magnitude and opposite polarities. Symmetry error, SymERR (%),
is measured and defined as:
∆SensPKG
=
(6)
100 (%)
×
Sens(25°C)(1)
where Sens(25°C)(1) is the programmed value of sensitivity
at TA = 25°C, and Sens(25°C)(2) is the value of sensitivity at
TA = 25°C after temperature cycling TA up to 150°C (L tempera-
ture device) or 125°C (K temperature device), down to –40°C,
and back up to 25°C.
Sens(B+)
Sens(B–)
1–
SymERR
=
100 (%)
×
(11)
where SensBx is as defined in equation 10, and B+ and B– are
positive and negative magnetic fields such that |B+| = |B–|.
Linearity Sensitivity Error. The A1308 and A1309 are
designed to provide linear output in response to a ramping
applied magnetic field. Consider two magnetic fields, B1 and B2.
Ideally, the sensitivity of a device is the same for both fields, for
a given supply voltage and temperature. Linearity error is present
when there is a difference between the sensitivities measured at
B1 and B2.
Ratiometry Error. The A1308 and A1309 provide ratiometric
output. This means that the Quiescent Voltage Output, VOUT(Q)
magnetic sensitivity, Sens, and clamp voltages, VCLPHIGH and
VCLPLOW, are proportional to the supply voltage, VCC. In other
words, when the supply voltage increases or decreases by a
certain percentage, each characteristic also increases or decreases
by the same percentage. Error is the difference between the
measured change in the supply voltage relative to 5 V and the
measured change in each characteristic.
,
Linearity Sensitivity Error, LINERR , is calculated separately for
positive (LinERR+) and negative (LinERR– ) applied magnetic
fields. LINERR (%) is measured and defined as:
Sens
The ratiometric error in quiescent voltage output, RatVOUT(Q)
(%), for a given supply voltage, VCC, is defined as:
(B+)(2)
1–
LinERR+
=
=
100 (%)
100 (%)
(7)
×
×
Sens(B+)(1)
VOUT(Q)(VCC) / V
OUT(Q)(5V)
Sens(B–)(2)
1–
RatVOUT(Q)
=
100 (%)
×
(12)
1–
LinERR–
VCC / 5 (V)
Sens
(B–)(1)
The ratiometric error in magnetic sensitivity, RatSens (%), for a
given supply voltage, VCC, is defined as:
where:
|VOUT(Bx)
V
|
–
OUT(Q)
SensBx
=
(8)
Sens(VCC) / Sens
VCC / 5 (V)
Bx
(5V)
1–
RatSens
=
100 (%)
(13)
×
and Bx are positive and negative magnetic fields, with respect to
the quiescent voltage output, such that
The ratiometric error in the clamp voltages, RatVOUTCLP (%), for
a given supply voltage, VCC, is defined as:
|B(+)(2)| > |B(+)(1)| and |B(–)(2)| > |B(–)(1)
The effective linearity error is:
|
VCLP(VCC) / V
CLP(5V)
1–
RatVOUTCLP
=
100 (%)
(14)
×
VCC / 5 (V)
LinERR max(|Lin
| |LinERR– |)
=
,
ERR+
(9)
where VCLP is either VCLPHIGH or VCLPLOW
.
Allegro MicroSystems, LLC
115 Northeast Cutoff
7
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
5秒后页面跳转
PCF8574资料解读：主要参数分析、引脚说明
AD637数据手册解读：主要特性、引脚及其功能解读、电气参数
ADUM1201资料手册解读：参数分析、引脚说明、应用分析
一文带你了解压敏电阻器在直流电路中的过压保护作用
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
