5秒后页面跳转
80C52-12D PDF预览

80C52-12D

更新时间: 2024-01-30 11:01:48
品牌 Logo 应用领域
TEMIC 微控制器
页数 文件大小 规格书
20页 227K
描述
CMOS 0 to 44 MHz Single-chip 8 Bit Microcontroller

80C52-12D 技术参数

生命周期:Obsolete零件包装代码:QFP
包装说明:QCCJ,针数:44
Reach Compliance Code:unknownECCN代码:3A001.A.2.C
HTS代码:8542.31.00.01风险等级:5.78
Is Samacsys:N具有ADC:NO
地址总线宽度:16位大小:8
最大时钟频率:12 MHzDAC 通道:NO
DMA 通道:NO外部数据总线宽度:8
JESD-30 代码:S-CQCC-J44JESD-609代码:e3
长度:16.4465 mmI/O 线路数量:32
端子数量:44最高工作温度:125 °C
最低工作温度:-55 °CPWM 通道:NO
封装主体材料:CERAMIC, METAL-SEALED COFIRED封装代码:QCCJ
封装形状:SQUARE封装形式:CHIP CARRIER
认证状态:Not QualifiedROM可编程性:MROM
座面最大高度:4.83 mm速度:12 MHz
最大压摆率:35 mA最大供电电压:5.5 V
最小供电电压:4.5 V表面贴装:YES
技术:CMOS温度等级:MILITARY
端子面层:TIN端子形式:J BEND
端子节距:1.27 mm端子位置:QUAD
宽度:16.4465 mmuPs/uCs/外围集成电路类型:MICROCONTROLLER
Base Number Matches:1

80C52-12D 数据手册

 浏览型号80C52-12D的Datasheet PDF文件第5页浏览型号80C52-12D的Datasheet PDF文件第6页浏览型号80C52-12D的Datasheet PDF文件第7页浏览型号80C52-12D的Datasheet PDF文件第9页浏览型号80C52-12D的Datasheet PDF文件第10页浏览型号80C52-12D的Datasheet PDF文件第11页 
80C32/80C52  
MATRA MHS  
The capture mode is illustrated in Figure 7.  
with the 16 bit value in registers RCAP2L and RCAP2H,  
which are preset by software. If EXEN2 = 1, then Timer  
2 still does the above, but with the added feature that a  
1-to-0 transition at external input T2EX will also trigger  
the 16 bit reload and set EXF2.  
Figure 7. Timer 2 in Capture Mode.  
The auto-reload mode is illustrated in Figure 8.  
Figure 8. Timer in Auto-Reload Mode.  
In the auto-reload mode there are again two options,  
which are selected by bit EXEN2 in T2CON.If  
EXEN2 = 0, then when Timer 2 rolls over it does not only  
set TF2 but also causes the Timer 2 register to be reloaded  
(MSB)  
(LSB)  
TF2  
EXF2  
RCLK  
TCLK  
EXEN2  
TR2  
C/T2  
CP/RL2  
The baud rate generator mode is selected by : RCLK = 1 and/or TCLK = 1.  
Symbol  
Position  
Name and Significance  
TF2  
T2CON.7  
Timer 2 overflow flag set by a Timer 2 overflow and must be cleared by software. TF2  
will not be set when either RCLK = 1 OR TCLK = 1.  
EXF2  
T2CON.6  
Timer 2 external flag set when either a capture or reload is caused by a negative  
transition on T2EX and EXEN2 = 1. When Timer 2 interrupt is enabled, EXF2 = 1 will  
cause the CPU to vector to the Timer 2 interrupt routine. EXF2 must be cleared by  
software.  
RCLK  
TCLK  
T2CON.5  
T2CON.4  
T2CON.3  
Receive clock flag. When set, causes the serial port to use Timer2 overflow pulses for its  
receive clock in modes 1 and 3. RCLK = 0 causes Timer 1 overflow to be used for the  
receive clock.  
Transmit clock flag. When set, causes the serial port to use Timer 2 overflow pulses for  
its transmit clock in modes 1 and 3. TCLK = 0 causes Timer 1 overflows to be used for  
the transmit clock.  
EXEN2  
Timer 2 external enable flag. When set, allows capture or reload to occur as a result of a  
negative transition on T2EX if Timer 2 is not being used to clock the serial port.  
EXEN2 = 0 causes Timer 2 to ignore events at T2EX.  
TR2  
T2CON.2  
T2CON.1  
Start/stop control for Timer 2. A logic 1 starts the timer.  
C/T2  
Timer or counter select. (Timer 2) 0 = Internal timer (OSC/12)  
1 = External event counter (falling edge triggered).  
CP/RL2  
T2CON.0  
Capture/Reload flag. When set, captures will occur on negative transitions at T2EX if  
EXEN 2 = 1. When cleared, auto reloads will occur either with Timer 2 overflows or  
negative transition at T2EX when EXEN2 = 1. When either RCLK = 1 or TCLK = 1, this  
bit is ignored and the timer is forced to auto-reload on Timer 2 overflow.  
8
Rev. E (31/08/95)  

与80C52-12D相关器件

型号 品牌 描述 获取价格 数据表
80C52-12R TEMIC CMOS 0 to 44 MHz Single-chip 8 Bit Microcontroller

获取价格

80C52-16 TEMIC CMOS 0 to 44 MHz Single Chip 8?bit Microntroller

获取价格

80C52-16/BMA ETC 8-Bit Microcontroller

获取价格

80C52-16/BQA ETC 8-Bit Microcontroller

获取价格

80C52-16D TEMIC CMOS 0 to 44 MHz Single-chip 8 Bit Microcontroller

获取价格

80C52-16R TEMIC CMOS 0 to 44 MHz Single-chip 8 Bit Microcontroller

获取价格