IDT71V3557, IDT71V3559, 128K x 36, 256K x 18, 3.3V Synchronous SRAMs with
ZBT™ Feature, 3.3V I/O, Burst Counter, and Flow-Through Outputs
Commercial and Industrial Temperature Ranges
Pin Definitions (1)
Symbol
Pin Function
I/O
Active
Description
A0-A17
Address Inputs
I
N/A
Synchronous Address inputs. The address register is triggered by a combination of the rising edge of CLK,
ADV/LD low, CEN low, and true chip enables.
ADV/LD
Advance / Load
I
N/A
ADV/LD is a synchronous input that is used to load the internal registers with new address and control when it
is sampled low at the rising edge of clock with the chip selected. When ADV/ is low with the chip
LD
deselected, any burst in progress is terminated. When ADV/LD is sampled high then the internal burst
counter is advanced for any burst that was in progress. The external addresses are ignored when ADV/LD is
sampled high.
R/W
Read / Write
Clock Enable
I
I
N/A
R/W signal is a synchronous input that identifies whether the current load cycle initiated is a Read or Write
access to the memory array. The data bus activity for the current cycle takes place one clock cycle later.
LOW
Synchronous Clock Enable Input. When CEN is sampled high, all other synchronous inputs, including clock
are ignored and outputs remain unchanged. The effect of CEN sampled high on the device outputs is as if
the low to high clock transition did not occur. For normal operation, CEN must be sampled low at rising edge
of clock.
CEN
Individual Byte
Write Enables
I
I
LOW
LOW
Synchronous byte write enables. Each 9-bit byte has its own active low byte write enable. On load write
cycles (When R/W and ADV/LD are sampled low) the appropriate byte write signal (BW1-BW4) must be valid.
The byte write signal must also be valid on each cycle of a burst write. Byte Write signals are ignored when
R/W is sampled high. The appropriate byte(s) of data are written into the device one cycle later. BW1-BW4
can all be tied low if always doing write to the entire 36-bit word.
BW1-BW4
Chip Enables
Synchronous active low chip enable. CE1 and CE2 are used with CE2 to enable the IDT71V3557/59. (CE1 or
CE2 sampled high or CE2 sampled low) and ADV/LD low at the rising edge of clock, initiates a deselect
cycle. The ZBTTM has a one cycle deselect, i.e., the data bus will tri-state one clock cycle after deselect is
initiated.
,
2
CE1 CE
CE2
Chip Enable
Clock
I
I
HIGH
N/A
Synchronous active high chip enable. CE2 is used with CE1 and CE2 to enable the chip. CE2 has inverted
polarity but otherwise identical to CE1 and CE2.
CLK
This is the clock input to the IDT71V3557/59. Except for OE, all timing references for the device are made
with respect to the rising edge of CLK.
I/O0-I/O31
I/OP1-I/OP4
Data Input/Output
Linear Burst Order
Output Enable
I/O
I
N/A
Data input/output (I/O) pins. The data input path is registered, triggered by the rising edge of CLK. The data
output path is flow-through (no output register).
LOW
LOW
Burst order selection input. When LBO is high the Interleaved burst sequence is selected. When LBO is low
the Linear burst sequence is selected. LBO is a static input, and it must not change during device operation..
LBO
I
Asynchronous output enable. OE must be low to read data from the 71V3557/59. When OE is HIGH the I/O
pins are in a high-impedance state. OE does not need to be actively controlled for read and write cycles. In
normal operation, OE can be tied low.
OE
TMS
TDI
Test Mode Select
Test Data Input
I
I
N/A
N/A
Gives input command for TAP controller. Sampled on rising edge of TDK. This pin has an internal pullup.
Serial input of registers placed between TDI and TDO. Sampled on rising edge of TCK. This pin has an
internal pullup.
Clock input of TAP controller. Each TAP event is clocked. Test inputs are captured on rising edge of TCK,
while test outputs are driven from the falling edge of TCK. This pin has an internal pullup.
TCK
TDO
Test Clock
I
N/A
N/A
Serial output of registers placed between TDI and TDO. This output is active depending on the state of the
TAP controller.
Test Data Output
O
Optional Asynchronous JTAG reset. Can be used to reset the TAP controller, but not required. JTAG reset
occurs automatically at power up and also resets using TMS and TCK per IEEE 1149.1. If not used TRST can
be left floating. This pin has an internal pullup.
JTAG Reset
(Optional)
I
I
LOW
HIGH
TRST
Synchronous sleep mode input. ZZ HIGH will gate the CLK internally and power down the IDT71V3557/3559 to
its lowest power consumption level. Data retention is guaranteed in Sleep Mode. This pin has an internal
pulldown.
ZZ
Sleep Mode
VDD
VDDQ
VSS
Power Supply
Power Supply
Ground
N/A
N/A
N/A
N/A
N/A
N/A
3.3V core power supply.
3.3V I/O Supply.
Ground.
5282 tbl 02
NOTE:
1. AllsynchronousinputsmustmeetspecifiedsetupandholdtimeswithrespecttoCLK.
6.422
5秒后页面跳转
STM32F030C6芯片介绍：主要参数分析、引脚配置说明、功耗及封装
PCF8591数据手册解读：参数、引脚说明
一文带你了解ss8050参数、引脚配置、应用指南
深入解析AD7606高性能多通道模数转换器：资料手册参数分析
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
